xr16c864iq Exar Corporation, xr16c864iq Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16c864iq
Manufacturer Part Number
xr16c864iq
Description
Quad Uart With Rx/tx Fifo Counters And 128-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16C864IQ.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XR16C864IQ
Manufacturer:
ADI
Quantity:
9 029
Company:
Part Number:
xr16c864iq-F
Manufacturer:
NAIS
Quantity:
420
Company:
Part Number:
xr16c864iq-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Company:
Part Number:
xr16c864iqTR-F
Manufacturer:
Exar Corporation
Quantity:
10 000
XR16C864
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
Pin Description
DIRECT MEMORY ACCESS INTERFACE
RXRDYC#
RXRDYD#
TXRDYC#
TXRDYD#
RXRDYB#
TXRDYB#
RXRDYA#
TXRDYA#
RXRDY#
TXRDY#
INTSEL
FSRS#
(IRQ#)
CSD#
(N.C.)
(N.C.)
N
INTB
INTC
INTD
INTA
AME
100-QFP
P
100
68
12
18
63
69
87
25
56
81
31
50
82
45
44
76
IN
5
#
T
(OD)
YPE
O
O
O
O
O
O
I
I
I
UART channels A-D Transmitter Ready (active low). These outputs provide the TX FIFO/
THR status for transmit channels A-D. See
these outputs become Transmit Direct Memory Access Request outputs. See TXDRQ pin
description for more details. If these outputs are unused, leave them unconnected.
When 16/68# pin is at logic 1, this input is chip select D (active low) to enable channel D
in the device.
When 16/68# pin is at logic 0, this input is not used.
When 16/68# pin is at logic 1 for Intel bus interface, this ouput becomes channel A inter-
rupt output. The output state is defined by the user and through the software setting of
MCR[3]. INTA is set to the active mode when MCR[3] is set to a logic 1. INTA is set to the
three state mode when MCR[3] is set to a logic 0 (default). See MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, this output becomes device inter-
rupt output (active low, open drain). An external pull-up resistor is required for proper
operation.
When 16/68# pin is at logic 1 for Intel bus interface, these ouputs become the interrupt
outputs for channels B, C, and D. The output state is defined by the user through the soft-
ware setting of MCR[3]. The interrupt outputs are set to the active mode when MCR[3] is
set to a logic 1 and are set to the three state mode when MCR[3] is set to a logic 0
(default). See MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, these outputs are unused and
will stay at logic zero level. Leave these outputs unconnected.
Interrupt Select (active high, input with internal pull-down).
When 16/68# pin is at logic 1 for Intel bus interface, this pin can be used in conjunction
with MCR bit-3 to enable or disable the INT A-D pins or override MCR bit-3 and enable
the interrupt outputs. Interrupt outputs are enabled continuously by making this pin a
logic 1. Making this pin a logic 0 allows MCR bit-3 to enable and disable the interrupt out-
put pins. In this mode, MCR bit-3 is set to a logic 1 to enable the continuous output. See
MCR bit-3 description for full detail. This pin must be at logic 0 in the Motorola bus inter-
face mode.
UART channels A-D Receiver Ready (active low). These outputs provide the RX FIFO/
RHR status for receive channels A-D. See
these outputs become Receive Direct Memory Access Request outputs. See RXDRQ pin
description for more details. If these outputs are unused, leave them unconnected.
Transmitter Ready (active low). This output is a logically wire-ORed status of TXRDY#
A-D. See
Receiver Ready (active low). This output is a logically wire-ORed status of RXRDY# A-D.
See
FIFO Status Register Select (active low input with internal pull-up).
The content of the FSTAT register is placed on the data bus when this pin becomes
active. However it should be noted, D0-D3 contain the inverted logic states of TXRDY#
A-D pins, and D4-D7 the logic states (un-inverted) of RXRDY# A-D pins. Address line is
not required when reading this status register.
Table
Table
5. If this output is unused, leave it unconnected.
5. If this output is unused, leave it unconnected.
4
D
ESCRIPTION
Table
Table
5. If Direct Memory Access is enabled,
5. If Direct Memory Access is enabled,
áç
áç
áç
áç
REV. 2.0.1