xr16m2752 Exar Corporation, xr16m2752 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16m2752
Manufacturer Part Number
xr16m2752
Description
High Performance Duart With 64-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16M2752.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16m2752IJ44-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16m2752IL32-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
Pin Description
REV. 1.0.0
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
ANCILLARY SIGNALS
DTRB#
DSRB#
RESET
RTSB#
CTSB#
XTAL1
XTAL2
CDB#
MFB#
N
RIB#
GND
GND
VCC
NC
AME
Center Pad
32-QFN
18, 19
P
13
17
12
26
20
IN
4
5
-
-
-
-
-
#
44-PLCC
44, 33
22, 12
P
N/A
23
28
27
29
30
31
19
13
21
IN
11
-
#
T
Pwr
Pwr
Pwr
YPE
O
O
O
O
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
I
I
I
I
I
I
-
UART channel B Request-to-Send (active low) or general purpose output.
This port must be asserted prior to using auto RTS flow control, see
EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-
duplex direction control, see FCTR[3] and EMSR[3].
UART channel B Clear-to-Send (active low) or general purpose input. It
can be used for auto CTS flow control, see EFR[7], and IER[7]. This input
should be connected to VCC when not used.
UART channel B Data-Terminal-Ready (active low) or general purpose
output. If this pin is not used, leave it unconnected.
UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has no
effect on the UART.
UART channel B Carrier-Detect (active low) or general purpose input. This
input should be connected to VCC when not used. This input has no effect
on the UART.
UART channel B Ring-Indicator (active low) or general purpose input. This
input should be connected to VCC when not used. This input has no effect
on the UART.
Multi-Function Output Channel B. This output pin can function as the
OP2B#, BAUDOUTB#, or RXRDYB# pin. One of these output signal func-
tions can be selected by the user programmable bits 1-2 of the Alternate
Function Register (AFR). These signal functions are described as follows:
1) OP2B# - When OP2B# (active low) is selected, the MF# pin is LOW
when MCR bit-3 is set HIGH (see MCR bit-3). MCR bit-3 defaults to a logic
0 condition after a reset or power-up.
2) BAUDOUTB# - When BAUDOUTB# function is selected, the 16X Baud
rate clock output is available at this pin.
3) RXRDYB# - RXRDYB# (active low) is intended for monitoring DMA data
transfers. See
Crystal or external clock input.
Crystal or buffered clock output.
Reset (active high) - A longer than 40 ns HIGH pulse on this pin will reset
the internal registers and all outputs. The UART transmitter output will be
held HIGH, the receiver input will be ignored and outputs are reset during
reset period (see
1.62 to 3.63V power supply.
Power supply common, ground.
The center pad on the backside of the 32-QFN package is metallic and
should be connected to GND on the PCB. The thermal pad size on the
PCB should be the approximate size of this center pad and should be sol-
der mask defined. The solder mask opening should be at least 0.0025"
inwards from the edge of the PCB thermal pad.
No Connect.
5
Table 2
Table 16
for more details.
).
D
ESCRIPTION
XR16M2752