pxas37kfbe NXP Semiconductors, pxas37kfbe Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
pxas37kfbe
Manufacturer Part Number
pxas37kfbe
Description
Xa 16-bit Microcontroller 32 K/1 K Otp/rom/romless, 8-channel 8-bit A/d, Low Voltage 2.7 V.5.5 V, I2c, 2 Uarts, 16 Mb Address Range
Manufacturer
NXP Semiconductors
Datasheet
1.PXAS37KFBE.pdf
(52 pages)
1. The XA-S3 I
2. The timer 1 overflow is used to clock the I
Philips Semiconductors
CR0, CR1, and CR2, the Clock Rate Bits
These three bits determine the serial clock frequency when the I
interface is in a master mode. An I
typical and can be derived from many oscillator frequencies. The
various serial rates are shown in Table 4. A variable bit rate may
also be used if Timer 1 is not required for any other purpose while
the I
Table 4 are unimportant when the I
In the slave modes, the hardware will automatically synchronize with
the incoming clock frequency.
Table 4. I
NOTES:
2000 Dec 01
0h (0000)
1h (0001)
2h (0010)
3h (0011)
4h (0100)
5h (0101)
6h (0110)
7h (0111)
Frequency Select
XA 16-bit microcontroller
32 K/1 K OTP/ROM/ROMless, 8-channel 8-bit A/D, low voltage (2.7 V–5.5 V),
I
(CR2, CR1, CR0)
may be used with care where higher rates are required by the application.
2
2
C, 2 UARTs, 16 MB address range
C hardware is in a master mode. The frequencies shown in
q
2
y
C Rate Control
2
C interface does not conform to the 400kHz I
Clock Divisor
Clock Divisor
(Timer 1)
160
272
352
20
40
68
88
2
2
C rate of 100kHz or lower is
C hardware is in a slave mode.
2
(Timer 1)
(116.65)
2
C interface. The resulting bit rate is 1/2 of the timer overflow rate.
8 MHz
(400)
(200)
90.91
29.41
22.73
50
1
1
1
2
(Timer 1)
2
(176.46)
(136.36)
C specification (which applies to rates greater than 100kHz) in all details, but
12 MHz
(300)
44.12
34.09
2
Example I
C
75
–
1
1
1
2
19
2
contains F8H, no relevant state information is available and no serial
The I
I2STA is an 8-bit read-only special function register. The three least
significant bits are always zero. The five most significant bits contain
the status code. There are 26 possible status codes. When I2STA
interrupt is requested. All other I2STA values correspond to defined
hardware interface states. When each of these states is entered, a
serial interrupt is requested (SI = “1”).
NOTE: A detailed I
information, including example driver code, will be provided in
a separate document.
C Rates at Specific Oscillator Frequencies
(Timer 1)
(235.29)
(181.82)
16 MHz
(400)
58.82
45.45
2
100
–
C Status Register, I2STA
1
1
1
2
2
(Timer 1)
C interface description and usage
(294.12)
(227.27)
20 MHz
(125)
73.53
56.82
–
–
1
1
1
2
(Timer 1)
(352.94)
(272.73)
24 MHz
(150)
88.24
68.18
–
–
Preliminary specification
1
1
1
2
XA-S3
(Timer 1)
(340.91)
(110.29)
(187.5)
30 MHz
85.23
–
–
–
1
1
1
2