tda3681 NXP Semiconductors, tda3681 Datasheet - Page 17
tda3681
Manufacturer Part Number
tda3681
Description
Multiple Voltage Regulator With Switch And Ignition Buffer
Manufacturer
NXP Semiconductors
Datasheet
1.TDA3681.pdf
(29 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
tda3681ATH
Manufacturer:
MITSUBISHI
Quantity:
22
Part Number:
tda3681ATH
Manufacturer:
HSOP20
Quantity:
20 000
Part Number:
tda3681J
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
tda3681J/N2S+112
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
tda3681J/N2S,112
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
tda3681J/N2S112
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
tda3681JR/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
tda3681JR/N2C
Manufacturer:
ST
Quantity:
1 271
Philips Semiconductors
Notes
1. Minimum operating voltage, only if V
2. The total quiescent current is measured in the standby mode. Therefore, the enable inputs of regulators 1, 3, 4 and
3. The voltage of the regulator drops as a result of a V
4. The rise and fall times are measured with a 10 k pull-up resistor and a 50 pF load capacitor.
5. The delay time depends on the value of the reset delay capacitor:
6. The delay time depends on the value of the reset delay capacitor:
7. The drop-out voltage of regulators 1 and 2 is measured between pins V
8. At current limit, I
9. The foldback current protection limits the dissipated power at short-circuit (see Fig.8).
10. The drop-out voltage is measured between pins BU and REG2.
11. The drop-out voltage of the power switch is measured between pins V
12. The maximum output current of the power switch is limited to 1.8 A when the supply voltage exceeds 18 V.
13. At short-circuit, I
2004 Mar 31
Ignition buffer
V
V
I
I
t
t
Temperature protection
T
T
OL
OH
PLH
PHL
j(sd)
j(hold)
SYMBOL
OL
OH
Multiple voltage regulator with switch and
ignition buffer
the power switch are grounded and R
of V
regulators 3 and 4 is measured between pins V
of at least 10 ms.
P2
drop.
LOW-level output voltage I
HIGH-level output
voltage
LOW-level sink current
HIGH-level source
current
LOW-to-HIGH
propagation time
HIGH-to-LOW
propagation time
junction temperature for
shutdown
junction temperature for
hold trigger
sc(SW)
m(REGn)
PARAMETER
of the power switch is held constant to a lower value than the continuous current after a delay
is held constant (see Fig.8).
P1
L(REG2)
I
V
V
V
V
IGNOUT
IGNOUT
has exceeded 6.5 V.
IGNOUT
IGNOUT
IGNIN
IGNIN
rising from 1.7 to 2.5 V
falling from 2.5 to 1.7 V
=
= 0 mA
= 0 mA
CONDITIONS
P2
0.8 V
4.5 V
; see Figs 10 and 11.
P1
and REGn.
drop for regulators 1 and 2. Regulators 3 and 4 drop as a result
17
t
t
d(RES)
d(SW)
P1
0
4.5
0.45
0.45
150
150
MIN.
P1
and SW.
=
=
and REGn. The drop-out voltage of
----- -
I
C
ch
----- -
I
C
ch
0.2
5.0
0.8
2.0
160
160
V
V
TYP.
C(th)
C(th)
=
=
C
C
0.8
5.25
500
500
170
170
Product specification
375
750
MAX.
TDA3681
10
10
3
3
s
s
UNIT
V
V
mA
mA
C
C
s
s