lt3990 Linear Technology Corporation, lt3990 Datasheet - Page 7

no-image

lt3990

Manufacturer Part Number
lt3990
Description
60v, 350ma Step-down Regulator With 2.5?a Quiescent Current And Integrated Diodes
Manufacturer
Linear Technology Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lt3990EDD
Manufacturer:
LT
Quantity:
10 000
Part Number:
lt3990EDD
Manufacturer:
LTNEAR
Quantity:
20 000
Part Number:
lt3990EDD#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
lt3990EDD#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
lt3990EDD-3.3
Manufacturer:
LT
Quantity:
10 000
Part Number:
lt3990EDD-5
Manufacturer:
LT
Quantity:
10 000
Part Number:
lt3990EMSE
Manufacturer:
LT
Quantity:
10 000
Part Number:
lt3990EMSE#PBF
Manufacturer:
LT
Quantity:
3 500
Part Number:
lt3990EMSE#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
lt3990EMSE#TRPBF
Manufacturer:
LT/凌特
Quantity:
20 000
pin FuncTions
FB (Pin 1/Pins 1, 2): The LT3990 regulates the FB pin to
1.21V. Connect the feedback resistor divider tap to this
pin.
EN/UVLO (Pin 2/Pin 4): The part is in shutdown when this
pin is low and active when this pin is high. The threshold
voltage is 1.21V going up with 32mV of hysteresis. Tie
to V
threshold is accurate only when V
is lower than 4.2V, ground EN/UVLO to place the part in
shutdown.
V
LT3990’s internal circuitry and to the internal power switch.
This pin must be locally bypassed.
GND (Pins 4, 5, Exposed Pad Pin 11/Pin 8, Exposed
Pad Pin 17): Ground. The exposed pad must be soldered
to the PCB.
SW (Pin 6/Pin 9): The SW pin is the output of an internal
power switch. Connect this pin to the inductor.
block Diagram
V
IN
IN
C1
(Pin 3/Pin 6): The V
IN
R
T
if shutdown feature is not used. The EN/UVLO
10
3
2
9
V
EN/UVLO
RT
PG
1.21V
IN
+
(4, 5)
GND
+
INTERNAL 1.21V REF
SHDN
IN
(DFN, MSOP)
1.09V
R2
pin supplies current to the
1
FB
+
IN
ERROR
R1
AMP
is above 4.2V. If V
V
C
200kHz TO 2.2MHz
+
SLOPE COMP
OSCILLATOR
Burst Mode
DETECT
IN
BOOST (Pin 7/Pin 11): This pin is used to provide a drive
voltage, higher than the input voltage, to the internal bipolar
NPN power switch.
BD (Pin 8/Pin 13): This pin connects to the anode of the
boost diode. This pin also supplies current to the LT3990’s
internal regulator when BD is above 3.2V.
PG (Pin 9/Pin 14): The PG pin is the open-drain output of
an internal comparator. PG remains low until the FB pin
is within 10% of the final regulation voltage. PG is valid
when V
RT (Pin 10/Pin 16): A resistor is tied between RT and
ground to set the switching frequency.
NC (Pins 3, 5, 7, 10, 12, 15, MSOP Only): No Connects.
These pins are not connected to internal circuitry and must
be left floating to ensure fault tolerance.
IN
is above 4.2V and EN/UVLO is high.
SWITCH LATCH
R
S
Q
D
BOOST
D
CATCH
BOOST
SW
BD
8
7
6
LT3990
C3
L1
C2
3990 BD

3990p
V
OUT

Related parts for lt3990