m27c160 STMicroelectronics, m27c160 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m27c160
Manufacturer Part Number
m27c160
Description
16 Mbit 2mb X8 Or 1mb X16 Uv Eprom And Otp Eprom
Manufacturer
STMicroelectronics
Datasheet
1.M27C160.pdf
(26 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
m27c160-100F1
Manufacturer:
ST
Quantity:
6 100
Company:
Part Number:
m27c160-100F1
Manufacturer:
SGS
Quantity:
2 312
Part Number:
m27c160-100F1
Manufacturer:
ST
Quantity:
20 000
Part Number:
m27c160-100F1L
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
m27c160-100F6
Manufacturer:
STM
Quantity:
5 800
Company:
Part Number:
m27c160-100F6
Manufacturer:
STM
Quantity:
6 990
M27C160
2.3
2.4
2.5
2.6
When in the standby mode, the outputs are in a high impedance state, independent of the G
input.
Two-line output control
Because EPROMs are usually used in larger memory arrays, this product features a 2-line
control function which accommodates the use of multiple memory connection. The two line
control function allows:
For the most efficient use of these two control lines, E should be decoded and used as the
primary device selecting function, while G should be made a common connection to all
devices in the array and connected to the READ line from the system control bus. This
ensures that all deselected memory devices are in their low power standby mode and that
the output pins are only active when data is required from a particular memory device.
System considerations
The power switching characteristics of Advanced CMOS EPROMs require careful
decoupling of the supplies to the devices. The supply current I
importance to the system designer: the standby current, the active current and the transient
peaks that are produced by the falling and rising edges of E.
The magnitude of the transient current peaks is dependent on the capacitive and inductive
loading of the device outputs. The associated transient voltage peaks can be suppressed by
complying with the two line output control and by properly selected decoupling capacitors. It
is recommended that a 0.1µF ceramic capacitor is used on every device between V
V
as close as possible to the device. In addition, a 4.7µF electrolytic capacitor should be used
between V
This capacitor should be mounted near the power supply connection point. The purpose of
this capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces.
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27C160 are in the
'1' state. Data is introduced by selectively programming '0's into the desired bit locations.
Although only '0's will be programmed, both '1's and '0's can be present in the data word.
The only way to change a '0' to a '1' is by die exposure to ultraviolet light (UV EPROM). The
M27C160 is in the programming mode when V
pulsed to V
pins. The levels required for the address and data inputs are TTL. V
6.25V ± 0.25V.
Presto III programming algorithm
The Presto III Programming Algorithm allows the whole array to be programed with a
guaranteed margin in a typical time of 52.5 seconds. Programming with Presto III consists of
SS
. This should be a high frequency type of low inherent inductance and should be placed
the lowest possible memory power dissipation,
complete assurance that output bus contention will not occur.
CC
IL
. The data to be programmed is applied to 16 bits in parallel to the data output
and V
SS
for every eight devices.
PP
input is at 12.5V, G is at V
CC
has three segments of
CC
is specified to be
Device description
IH
and E is
CC
and
9/26