is62vv25616ll Integrated Silicon Solution, Inc., is62vv25616ll Datasheet
is62vv25616ll
Related parts for is62vv25616ll
is62vv25616ll Summary of contents
Page 1
... Output Enable inputs, CE and OE. The active LOW Write Enable (WE) controls both writing and reading of the memory. A data byte allows Upper Byte (UB) and Lower Byte (LB) access. The IS62VV25616LL is packaged in the JEDEC standard 44-pin TSOP (Type II) and 48-pin mini BGA (7.2mm x 8.7mm). 256K x 16 DECODER ...
Page 2
... IS62VV25616LL PIN CONFIGURATIONS 44-Pin TSOP (Type II I/O0 7 I/O1 8 I/ GND 12 I/O4 13 I/O5 14 I/ A16 18 A15 19 A14 20 A13 21 A12 22 PIN DESCRIPTIONS A0-A17 Address Inputs I/O0-I/O15 Data Inputs/Outputs CE Chip Enable Input OE Output Enable Input WE Write Enable Input ...
Page 3
... IS62VV25616LL OPERATING RANGE Range Ambient Temperature Commercial 0°C to +70°C Industrial –40°C to +85°C ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND TERM V Vdd Related to GND DD T Storage Temperature STG P Power Dissipation T Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied ...
Page 4
... IS62VV25616LL AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load AC TEST LOADS 3070 2.8V OUTPUT 30 pF Including jig and scope Figure 1 4 Unit 0. 0. 0.9V See Figures 1 and 2 3150 Figure 2 Integrated Silicon Solution, Inc. — www.issi.com — ...
Page 5
... IS62VV25616LL POWER SUPPLY CHARACTERISTICS Symbol Parameter I Vdd Dynamic Operating V CC Supply Current I Operating Supply 1 CC Current I TTL Standby Current 1 SB (TTL Inputs) OR ULB Control I CMOS Standby 2 SB Current (CMOS Inputs ULB Control Note address and data inputs are cycling at the maximum frequency means no input lines change. ...
Page 6
... IS62VV25616LL AC WAVEFORMS (Address Controlled) ( READ CYCLE NO. 1 (1,2) ADDRESS D OUT PREVIOUS DATA VALID AC WAVEFORMS (1,3) (CE, OE, AND UB/LB Controlled) READ CYCLE NO. 2 ADDRESS LZCE LB LZB HIGH-Z D OUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE, UB Address is valid prior to or coincident with CE LOW transition. ...
Page 7
... IS62VV25616LL WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time Write End t SCE t Address Setup Time to Write End AW t Address Hold from Write End HA t Address Setup Time SA LB, UB Valid to End of Write t PWB WE Pulse Width t PWE t Data Setup to Write End ...
Page 8
... IS62VV25616LL WRITE CYCLE NO. 2 (WE Controlled HIGH During Write Cycle) ADDRESS OE CE LOW UB DATA UNDEFINED OUT D IN (WE Controlled LOW During Write Cycle) WRITE CYCLE NO. 3 ADDRESS OE LOW CE LOW UB DATA UNDEFINED OUT VALID ADDRESS ...
Page 9
... IS62VV25616LL WRITE CYCLE NO. 4 (UB/LB Controlled) ADDRESS OE CE LOW WE UB HZWE D OUT DATA UNDEFINED D IN DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter V Vdd for Data Retention DR I Data Retention Current DR t Data Retention Setup Time SDR t Recovery Time RDR DATA RETENTION WAVEFORM ...
Page 10
... IS62VV25616LL-70M MiniBGA (7.2mmx8.7mm) 85 IS62VV25616LL-85T TSOP (Type II) IS62VV25616LL-85M MiniBGA (7.2mmx8.7mm) Industrial Range: –40°C to +85°C Speed Order Part No. (ns) 70 IS62VV25616LL-70TI IS62VV25616LL-70MI 85 IS62VV25616LL-85TI IS62VV25616LL-85MI 10 Package TSOP (Type II) MiniBGA (7.2mmx8.7mm) TSOP (Type II) MiniBGA (7.2mmx8.7mm) Integrated Silicon Solution, Inc. — www.issi.com — ISSI ® ...