at27c516 ATMEL Corporation, at27c516 Datasheet

Page 1

... PLCC and VSOP packages. The device features two-line control (CE, OE) to eliminate bus contention in high-speed systems. With 32K word storage capability, the AT27C516 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. ...

Page 2

... A0 - A14 O0 - O15 CE OE PGM NC Note: 2.1 40-lead VSOP (Type 1) Top View 2.2 44-lead PLCC Top View Note: PLCC Package Pins 1 and 23 are Don’t Connect. AT27C516 2 Function Addresses Outputs Chip Enable Output Enable Program Strobe No Connect Both GND pins must be connected A10 ...

Page 3

... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability (1) AT27C516 3 ...

Page 4

... ( A14 = except A9 which is set to V and A0 which is toggled select the Device Code byte. IH will cause a slight increase AT27C516 -40°C - 85°C 5V ± 10% Min Max ± 1 ± 0.3V 100 + 0. -0.6 0.8 2 0.5 CC 0.4 2.4 ...

Page 5

... Condition 0.8V and after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C516 AT27C516 -45 -70 Min Max Min Max 0.0V and V = 3.0V. Timing mea ...

Page 6

... Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C516 < (10 Note 100 pF including jig L capacitance, except -45 and -70 devices, where ...

Page 7

... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C516 at 0.1 µF capacitor is required across V voltage transients. 0362E–EPROM–1/08 (1) and 2.0V for AT27C516 and ground to suppress spurious ...

Page 8

... This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 50 µsec ± 5%. 17. Atmel’s AT27C516 Integrated Product Identification Code Codes A0 Manufacturer 0 ...

Page 9

... After the word verifies properly, the next address is selected until all have been checked. V are read again and compared with the original data to determine if the device passes or fails. 0362E–EPROM–1/08 is raised to 13.0V. Each address is first programmed with one 50 µ then lowered to 5.0V and V PP AT27C516 5.0V. All words CC 9 ...

Page 10

... Plastic Thin Small Outline Package (VSOP) AT27C516 10 Ordering Code Package AT27C516-45JI 44J AT27C516-45VI 40V AT27C516-70JI 44J AT27C516-70VI 40V Ordering Code Package AT27C516-45JU 44J AT27C516-70JU Package Type Operation Range (2) Industrial (-40° 85° C) (2) Operation Range Industrial (-40° 85° C) 0362E–EPROM–1/08 ...

Page 11

... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0362E–EPROM–1/08 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C516 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 4 ...

Page 12

... This package conforms to JEDEC reference MO-142, Variation CA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27C516 12 PIN SEATING PLANE ...

Page 13

... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2008 Atmel Corporation. All rights reserved. Atmel Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...