m62499fp Mitsumi Electronics, Corp., m62499fp Datasheet
![no-image](/images/manufacturer_photos/0/4/452/mitsumi_electronics__corp__sml.jpg)
m62499fp
Related parts for m62499fp
m62499fp Summary of contents
Page 1
... Port) (3-State Port) MITSUBISHI SOUND PROCESSORS M62499FP PACKAGE 64P6N 64pinQFP (Pitch:0.8mm) *BBE is the registration brand of the BBE Sound company. As for this IC, only the brand of BBE and the person who was permitted to use a patent can do sale and supply. ...
Page 2
... MCU Interface ALC sw10 Amp sw8 sw9 Vocal Cut sw2 sw4 3K sw5 sw1 sw3 MITSUBISHI SOUND PROCESSORS M62499FP sw11 Amp sw7 OUTPUT1 16 TBASS1-3 15 TBASS1-2 14 TBASS1-1 ...
Page 3
... ALC sw10 Amp sw8 sw9 Vocal Cut sw2 sw4 3K sw5 sw1 sw3 MITSUBISHI SOUND PROCESSORS M62499FP Open collectoroutput Three state output + 0.1µ sw11 Amp sw7 ...
Page 4
... SOUND CONTROLLER WITH T-BASS and BBE Mono/Lch/Rch SELECTOR MITSUBISHI SOUND PROCESSORS M62499FP ( 4 / 19) ...
Page 5
... Power dissipation Pd K Thermal derating Topr Operating temperature Tstg Storage temperature THERMAL DERATING 1.5 1.0W 1.0 0 AMBIENT TEMPERATURE Ta [°C] MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE Conditions Ta 25°C Ta>25°C, (Note1)PC Board 600mW 65 75 100 150 125 Limits Units +4.0 V -4.0 6.0 V ...
Page 6
... CLOCK are "H" setting,it doesn't accept LATCH.) MITSUBISHI SOUND PROCESSORS SOUND CONTROLLER WITH T-BASS and BBE Symbol Conditions MIN VCC 3.25 -3.75 VEE VDD VDD VCC 4.75 VIH VDD-1 0 VIL D1 D16 M62499FP Limits Units TYP MAX 3.5 3.75 V -3.5 -3.25 5.0 5.25 V VDD V 0.8 V LATCH Signal ...
Page 7
... DATA hold time t HD LATCH setup time LATCH pulse width WHL MITSUBISHI SOUND PROCESSORS SOUND CONTROLLER WITH T-BASS and BBE WHC WLC 75% 25 Parameter M62499FP WHC Limits Units typ Min Max 4 1.6 1.6 0.4 µsec 0.4 0.8 0 ...
Page 8
... M62499FP Fixation bit (For address) D13 D14 D15 D16 Rec mute (1)-2 SETTING CODE OF GAIN CONTROL Gain ...
Page 9
... T-Bass OFF 5dB 0 1 10dB 1 1 15dB 0 0 20dB Prohibition Prohibition 1 1 MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE (Try state port output mode) (2)-2 Ss0 Ss1 Port5 Low Port Port 1 0 open open ...
Page 10
... By the equal to or less than -70dB setting,it sometimes shifts little. SETTING CODE OF VOL AMP. GAIN (4)-1 SWITCHING VOL Amp. gain 16dB 15dB 14dB 13dB 12dB 11dB 10dB 9dB MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE ...
Page 11
... Gain is setting code name. Depending on the fixed number of putting outside,fixed gain doesn't sometimes output. MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE TREBLE ...
Page 12
... SOUND CONTROLLER WITH T-BASS and BBE - + - + + - + - + - + MITSUBISHI SOUND PROCESSORS M62499FP - + + - + - + - + 19) ...
Page 13
... M62499FP A part:3dB ATT L/R5 L/ R(Vol) constant 0 1 (About 30K ) in the control VL0 VL1 VL2 VR0 VR1 VR2 ...
Page 14
... Resonance park Q 10 Boost quantity Gv Then C1= log Resonance Frequency fo OUT Resonance park Boost quantity Gv C1 Then C1= log (Ex.) Bass band setting [f=100Hz] R1=6.8K ,C1=C2=0.068µ F M62499FP R1•(R2+R3)•C1•C2 1 C1•C2• C1+C2 R1 R2+ R1•(R2+R3)•C1•C2 1 C1• ...
Page 15
... ASPECT ALC CIRCUIT Lch and the identical block 3.7V 10K 220K 32pin Mute signal 1.85V C1: 0.33u M62499FP OUTPUT MUTE (WITH SOFT MUTE) NEGATIVE ASPECT MIX. Center frequency C1•C2•R1•R2 [Hz (C1•C2•R2)/R1 / (C1+C2) (EX.) BASS BAND setting f=60Hz R1=2.6K , R2=120K C1=0.15µ, C2=0.15µ ...
Page 16
... With output pin voltage being the inside of the range of D GND~9V and using. 2) Output port:Try state With output pin voltage being the inside of the range of D GND~D VDD and using. MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE 19,20,24,25,26,27Pin Io=10mA,Vc=0.2V(typ) D GND 21,22Pin VDD=5.0V 4 ...
Page 17
... BBE BLOCK This system brings a replay sound close to the field sound boundlessly. Low boost (f=20HZ)=+3dB fixation High boost (f=10KHZ)=+11dB/+7dB/+3dB possible variably IN MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE VCA OUT 19) ...
Page 18
... Distortion factor Output noise voltage (Remaining noise voltage) Crosstalk between channels Volume step resolution ability Profit deviation between volume MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE Symbol Test condition ICC No signal setting. IEE No signal setting. No signal setting. IDD Symbol ...
Page 19
... PORT OUTPUT (VDD=5.0V setting) Parameter PORT OUTPUT REMAINDER VOLTAGE 19,20,24,25,26,27Pin (Open collector output) THREE STATE HIGH OUTPUT THREE STATE LOW OUTPUT MITSUBISHI SOUND PROCESSORS M62499FP SOUND CONTROLLER WITH T-BASS and BBE Symbol Test condition Vo=0.04Vrms , RL=10K ,JIS-A GC MAX Rg=10K ,Gain:14dB~0dB GC STEP ...