PS21963-A Mitsumi Electronics, Corp., PS21963-A Datasheet
PS21963-A
Available stocks
Related parts for PS21963-A
PS21963-A Summary of contents
Page 1
... MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21963-A INTEGRATED DRIVE, PROTECTION AND SYSTEM CONTROL FUNCTIONS • For upper-leg IGBT : Drive circuit, High voltage isolated high-speed level shifting, Control supply under-voltage (UV) protection. S • For lower-leg IGBT : Drive circuit, Control supply under-voltage protection (UV), Short circuit protection (SC) ...
Page 2
... Fig. 2 LONG TERMINAL TYPE PACKAGE OUTLINES (PS21963-A) 38 0.5 0.28 35 0.3 1.778 0.2 17 Type name QR Lot No. Code 18 0.28 2.54 3.08 0.2 14 2.54(=35.56) 0.5 HEAT SINK SIDE Fig. 3 ZIGZAG TERMINAL TYPE PACKAGE OUTLINES (PS21963-C) 38 0.5 0.28 35 0.3 1.778 0.2 17 Type name QR Lot No. ...
Page 3
... When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Collector current waveform 0 2 PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE C2 C1 (Note 7) (Note 5) H-side IGBT S DIP-IPM ...
Page 4
... Inverter part 125 C, non-repetitive, less than 60Hz, Sinusoidal minutes, All connected pins to heat-sink plate Control terminals 3mm T point C Heat sink side Power terminals PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Ratings 450 500 600 10 20 27.0 (Note 1) –20~+125 100 C). However 125 100 C) ...
Page 5
... Trip level Reset level T 125 C j Trip level Reset level Applied between PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — — — determined by the thickness and the thermal th(c-f) Limits Min. Typ. Max. — 2. 1.70 — 2.30 1 ...
Page 6
... For each input signal, T 100 300V 15V P.F = 0.8, sinusoidal PWM, T 125 C, T 100 C (Note Between V -N (including surge) NC PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — 0.59 0.78 — — 10 — (Note 7) –50 100 Limits Min. Typ. ...
Page 7
... Fig. 6 THE DIP-IPM INTERNAL CIRCUIT V UFB VFB WFB HVIC IGBT1 OUT P V COM US IGBT2 OUT IGBT3 OUT V WS IGBT4 LVIC U OUT V CC IGBT5 V OUT IGBT6 OUT Fo CIN V NO GND V CIN NO PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM P Di1 U Di2 V Di3 W Di4 Di5 Di6 N Jun. 2005 ...
Page 8
... Normal operation : IGBT ON and carrying current. Control input Protection circuit state Control supply voltage V Output current Ic Error output SET RESET reference voltage CR circuit time constant DELAY the circuits start to operate when next input is applied. Dr RESET SET PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE RESET b6 b7 Jun. 2005 ...
Page 9
... UV DBt line 10k (min) pull-down resistor. Therefore, when using an external Wiring inductance should be less than 10nH. Equivalent to the inductance of a copper pattern with length=17mm, width=3mm, and thickness=100 m Shunt resistor N PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE RESET c5 c6 DIP-IPM , 3.3k (min) (Logic) ...
Page 10
... GND CIN Long wiring here might cause SC level fluctuation and malfunction. and V terminals as shown in Fig. PS21963/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE These wires should be connected terminals directly and separated from the main output wires Long wiring here might Long wiring here might cause short-circuit ...