nx3v1t384 NXP Semiconductors, nx3v1t384 Datasheet

no-image

nx3v1t384

Manufacturer Part Number
nx3v1t384
Description
Low-ohmic Single-pole Single-throw Analog Switch
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
nx3v1t384GM
Manufacturer:
NXP
Quantity:
5 000
Part Number:
nx3v1t384GM
Manufacturer:
NXP/恩智浦
Quantity:
20 000
1. General description
2. Features
The NX3V1T384 provides one single-pole single-throw analog switch function. It has two
input/output terminals (Y and Z) and an active LOW enable input pin (E). When E is HIGH,
the analog switch is turned off.
Schmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise
and fall times across the entire V
A low input voltage threshold allows pin E to be driven by lower level logic signals without
a significant increase in supply current I
switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level
translation.
The NX3V1T384 allows signals with amplitude up to V
from Z to Y. Its ultra-low ON resistance (0.3 ) and flatness (0.1 ) ensures minimal
attenuation and distortion of transmitted signals.
I
I
I
I
I
I
I
I
I
I
I
NX3V1T384
Low-ohmic single-pole single-throw analog switch
Rev. 01 — 21 September 2009
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
High noise immunity
ESD protection:
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78B Class II Level A
Enable input accepts voltages above supply voltage
1.8 V control logic at V
Very low supply current, even when input is below V
High current handling capability (500 mA continuous current under 3.3 V supply)
Specified from 40 C to +85 C and from 40 C to +125 C
N
N
N
N
N
N
N
N
0.8
0.5
0.3
0.25
0.25
HBM JESD22-A114F Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
(typical) at V
(typical) at V
(typical) at V
(typical) at V
(typical) at V
CC
CC
CC
CC
CC
CC
= 1.4 V
= 1.65 V
= 2.3 V
= 3.6 V
= 2.7 V
= 4.3 V
CC
range from 1.4 V to 4.3 V.
CC
. This makes it possible for the NX3V1T384 to
CC
CC
to be transmitted from Y to Z or
Product data sheet

Related parts for nx3v1t384

nx3v1t384 Summary of contents

Page 1

... Low-ohmic single-pole single-throw analog switch Rev. 01 — 21 September 2009 1. General description The NX3V1T384 provides one single-pole single-throw analog switch function. It has two input/output terminals (Y and Z) and an active LOW enable input pin (E). When E is HIGH, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise ...

Page 2

... The pin 1 indicator is located on the lower left corner of the device, below the marking code. 6. Functional diagram E Z 001aag476 Fig 1. Logic symbol NX3V1T384_1 Product data sheet Low-ohmic single-pole single-throw analog switch Description TSSOP5 plastic thin shrink small outline package; 5 leads; body width 1.25 mm XSON6 plastic extremely thin small outline package ...

Page 3

... V) 4 enable input (active LOW) 5 not connected 6 supply voltage Switch ON-state OFF-state Rev. 01 — 21 September 2009 NX3V1T384 NX3V1T384 n.c. GND 001aaj987 Transparent top view Pin configuration SOT886 (XSON6) © NXP B.V. 2009. All rights reserved. ...

Page 4

... pulsed duration, < duty cycle; peak current +125 C amb derates linearly with 4.0 mW/K. tot derates linearly with 7.8 mW/K. tot Conditions enable input 1 4 Rev. 01 — 21 September 2009 NX3V1T384 Min Max Unit 0.5 +4.6 V [1] 0.5 +4.6 V [ ...

Page 5

... Figure Figure GND Rev. 01 — 21 September 2009 NX3V1T384 +125 C amb amb Typ Max Min ( 1 ...

Page 6

... Fig 6. Test circuit for measuring ON-state leakage T amb Min ; CC Figure amb Rev. 01 — 21 September 2009 NX3V1T384 GND 0 0 open circuit current = + +125 C amb [1] Typ Max Min 0.8 1.9 - 0.5 0 ...

Page 7

... Fig 7. Test circuit for measuring ON resistance NX3V1T384_1 Product data sheet Low-ohmic single-pole single-throw analog switch 001aai599 (1) V (2) V (3) V (4) V (5) V (6) V Fig 8. Rev. 01 — 21 September 2009 NX3V1T384 1.6 1.2 (1) 0.8 (2) (3) (4) 0.4 ( 2.7 V. ...

Page 8

... T Fig 10. ON resistance as a function of input voltage; 001aah802 0 0.4 0 (V) I (1) T (2) T (3) T (4) T Fig 12. ON resistance as a function of input voltage; Rev. 01 — 21 September 2009 NX3V1T384 (1) (2) (3) ( 125 C. amb = 85 C. amb = 25 C. amb = 40 C. amb ...

Page 9

... Figure and V = 1.5 V, 1.8 V, 2.5 V and 3.3 V respectively. amb CC Rev. 01 — 21 September 2009 NX3V1T384 0 0.4 (1) (2) (3) ( 125 C. amb ( amb ( amb ( ...

Page 10

... Table 10. Input 11. Input 2 Rev. 01 — 21 September 2009 NX3V1T384 dis V X switch switch enabled disabled 001aai600 Output 1.5 V EXT 001aai601 Load © NXP B.V. 2009. All rights reserved. ...

Page 11

... MHz 0.1 nF see Figure 21 gen Y/Z Z Rev. 01 — 21 September 2009 NX3V1T384 = GND or V (unless otherwise amb Min Typ [1] Figure 17 - 0.05 - 0.03 - 0.01 - 0.01 - 0. Figure 20 - 0 gen - 6 ...

Page 12

... Y/Z Z 0.5V 0. logic off on input ( Rev. 01 — 21 September 2009 NX3V1T384 001aai603 0. Z/Y dB 001aai604 001aai605 off V ct 001aai606 © NXP B.V. 2009. All rights reserved ...

Page 13

... Fig 21. Test circuit for measuring charge injection NX3V1T384_1 Product data sheet Low-ohmic single-pole single-throw analog switch logic off on input ( Rev. 01 — 21 September 2009 NX3V1T384 CC R gen Z/Y V gen GND 001aai607 off V O 001aai608 © NXP B.V. 2009. All rights reserved ...

Page 14

... Low-ohmic single-pole single-throw analog switch 1 scale (1) ( 0.30 0.25 2.25 1.35 0.65 0.15 0.08 1.85 1.15 REFERENCES JEDEC JEITA MO-203 SC-88A Rev. 01 — 21 September 2009 NX3V1T384 detail 2.25 0.46 1.3 0.425 0.3 0.1 2.0 0.21 EUROPEAN PROJECTION SOT353-1 ( ...

Page 15

... Low-ohmic single-pole single-throw analog switch scale 1.05 0.35 0.40 0.6 0.5 0.95 0.27 0.32 REFERENCES JEDEC JEITA MO-252 Rev. 01 — 21 September 2009 NX3V1T384 4 ( EUROPEAN PROJECTION SOT886 ISSUE DATE 04-07-15 04-07-22 © NXP B.V. 2009. All rights reserved ...

Page 16

... Personal Digital Assistant 15. Revision history Table 14. Revision history Document ID Release date NX3V1T384_1 20090921 NX3V1T384_1 Product data sheet Low-ohmic single-pole single-throw analog switch Data sheet status Change notice Product data sheet - Rev. 01 — 21 September 2009 NX3V1T384 Supersedes - © NXP B.V. 2009. All rights reserved ...

Page 17

... Export might require a prior authorization from national authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. http://www.nxp.com salesaddresses@nxp.com Rev. 01 — 21 September 2009 NX3V1T384 © NXP B.V. 2009. All rights reserved ...

Page 18

... Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com All rights reserved. Date of release: 21 September 2009 Document identifier: NX3V1T384_1 ...

Related keywords