isp1106 NXP Semiconductors, isp1106 Datasheet - Page 20

no-image

isp1106

Manufacturer Part Number
isp1106
Description
Advanced Universal Serial Bus Transceivers
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
isp1106DH
Manufacturer:
ROHM
Quantity:
1 830
Part Number:
isp1106DH
Manufacturer:
PHILIPS
Quantity:
4 426
Part Number:
isp1106DH
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
isp1106DH
Quantity:
879
Part Number:
isp1106W
Manufacturer:
PHI
Quantity:
20 000
Part Number:
isp1106WTM
Manufacturer:
SKYWORKS
Quantity:
3 000
Part Number:
isp1106WTM
Manufacturer:
ST-ERICSSON
Quantity:
20 000
Part Number:
isp1106WTS
Manufacturer:
ST-ERICSSON
Quantity:
28 912
Part Number:
isp1106WTS
Manufacturer:
ST
0
Part Number:
isp1106WTS
Manufacturer:
ST-ERICSSON
Quantity:
20 000
Philips Semiconductors
9397 750 08872
Product data
14.4 Manual soldering
14.5 Package related soldering information
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the
need for removal of corrosive residues in most applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 C.
Table 18:
[1]
[2]
[3]
[4]
[5]
Package
BGA, HBGA, LFBGA, SQFP, TFBGA
HBCC, HLQFP, HSQFP, HSOP, HTQFP,
HTSSOP, HVQFN, SMS
PLCC
LQFP, QFP, TQFP
SSOP, TSSOP, VSO
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods .
These packages are not suitable for wave soldering as a solder joint between the printed-circuit board
and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top
version).
If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is only suitable for LQFP, QFP and TQFP packages with a pitch (e) equal to or larger
than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[3]
, SO, SOJ
Suitability of surface mount IC packages for wave and reflow soldering
methods
Rev. 06 — 30 November 2001
Soldering method
Wave
not suitable
not suitable
suitable
not recommended
not recommended
ISP1105/1106/1107
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
[2]
Advanced USB transceivers
[3][4]
[5]
Reflow
suitable
suitable
suitable
suitable
suitable
[1]
20 of 24

Related parts for isp1106