mc68hc711d3 Freescale Semiconductor, Inc, mc68hc711d3 Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc68hc711d3
Manufacturer Part Number
mc68hc711d3
Description
M Hc11 Microcontrollers Microcontroller
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC68HC711D3.pdf
(138 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc68hc711d3CFN2
Manufacturer:
DIODES
Quantity:
12 000
Company:
Part Number:
mc68hc711d3CFN2
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
mc68hc711d3CFN2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
mc68hc711d3CFN3
Manufacturer:
FREESCALE
Quantity:
8 831
Company:
Part Number:
mc68hc711d3CFNE2
Manufacturer:
ALLEGEO
Quantity:
4 492
Company:
Part Number:
mc68hc711d3CFNE2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
mc68hc711d3CFNE3
Manufacturer:
SGS
Quantity:
6 218
ROMON — PROM Enable Bit
2.4 Programmable Read-Only Memory (PROM)
The MC68HC711D3 has 4-Kbytes of one-time programmable read-only memory (OTPROM). The PROM
address is $F000–$FFFF in all modes except expanded multiplexed. In expanded- multiplexed mode, the
PROM is located at $7000–$7FFF after reset.
The on-chip read-only memory (ROM) of an MC68HC711D3 is programmed in MCU mode. In this mode,
the PROM is programmed through the MCU in the bootstrap or test modes. The erased state of a PROM
byte is $FF.
Using the on-chip OTPROM programming feature requires an external 12-volt nominal power supply
(V
As described in the following subsections, these two methods of programming and verifying EPROM are
possible:
2.4.1 Programming an Individual EPROM Address
In this method, the MCU programs its own EPROM by controlling the PPROG register. Use these
procedures to program the EPROM through the MCU with:
Freescale Semiconductor
PP
1. Programming an individual EPROM address
2. Programming the EPROM with downloaded data
This bit is set out of reset, enabling the EPROM or OTPROM in all modes. This bit is writable once in
normal modes (SMOD = 0), but is writable at any time in special modes (SMOD = 1).
•
•
•
EPROG
). Normal programming is accomplished using the OTPROM programming register (PPROG).
1 = PROM is present in the memory map.
0 = PROM is disabled from the memory map.
The ROMON bit set in the CONFIG register
The 12-volt nominal programming voltage present on the XIRQ/V
The IRQ pin must be pulled high.
LDAB
STAB
STAA
LDAB
STAB
JSR
CLR
In expanded mode out of reset, the EPROM or OTPROM is located at
$7000–$7FFF. In all other modes, the PROM resides at $F000–$FFFF.
#$20
$003B
$0,X
#$21
$003B
DLYEP
$003B
Set ELAT bit (PGM = 0) to enable
EPROM latches.
Store data to EPROM address
Set PGM bit with ELAT = 1 to enable
EPROM programming voltage
Delay 2–4 ms
Turn off programming voltage and set
to READ mode
MC68HC711D3 Data Sheet, Rev. 2.1
NOTE
Programmable Read-Only Memory (PROM)
PP
pin
31