dac1054 National Semiconductor Corporation, dac1054 Datasheet
dac1054
Available stocks
Related parts for dac1054
dac1054 Summary of contents
Page 1
... The DAC1054 also has a data readback function which can be used by the microprocessor to verify that the desired input word has been properly latched into the DAC1054’s ...
Page 2
... Operating Ratings 5 mA Supply Voltage 30 mA Supply Voltage Difference (AV 950 mW Temperature Range DAC1054CIN DAC1054CIWM 2000V DAC1054CMJ 883 200V 65V REF BIAS e 10 MHz unless otherwise specified Boldface limits apply for T CLK ...
Page 3
Converter Electrical Characteristics The following specifications apply for AV CC the analog outputs – pins and 23) and f e All other limits apply for T T from MIN MAX Symbol Parameter DIGITAL ...
Page 4
... J Note 9 Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level) Note 10 A monotonicity of 10 bits for the DAC1054 means that the output voltage changes in the same direction (or remains constant) for each increase in the input code Note 11 Integral linearity error is the maximum deviation of the output from the line drawn between zero and full-scale (excluding the effects of zero error and full- ...
Page 5
Typical Converter Performance Characteristics Zero Error vs Temperature Zero Error PSRR vs Temperature Typical Reference Performance Characteristics Bandgap Voltage vs Temperature Full-Scale Error vs Temperature Full-Scale Error PSRR vs Temperature Integral Non-Linearity Error vs Temperature Line Regulation vs Temperature TL ...
Page 6
TRI-STATE Test Circuits and Waveforms Timing Waveforms Data Input Timing Timing Diagrams FIGURE 1 Write to One DAC with Update of Output ( 11437 – 11437 – 7 Data Output Timing TL H 11437 – ...
Page 7
Timing Diagrams (Continued) DACs are written to MSB first DAC1 is written to first then DACs 2 3 and 4 FIGURE 2 Write to All DACs with Update of Outputs (AU FIGURE 3 Read One DAC DO LSB First DO ...
Page 8
... The digital and analog power supply CC AV (19) pins The power supply range of the CC DAC1054 – guarantee accuracy it is required that the AV and DV pins be bypassed separately CC with bypass capacitors tantalum in parallel with ceramic AU(11) When this pin is taken low all DAC outputs ...
Page 9
... DAC register a shift register a current output DAC and an output amplifier In addition the DAC1054 has an onboard bandgap reference and a logic unit which controls the inter- nal operation of the DAC1054 and interfaces it to micro- processors Each of the four internal 10-bit DACs uses a modified R-2R ...
Page 10
... Digital Interface The DAC1054 has two interface modes a WRITE mode and a READ mode The WRITE mode is used to convert a 10-bit digital input word into a voltage The READ mode is used to read back the digital data that was sent to one or all of the DACs The WRITE mode maximum clock rate is ...
Page 11
... Power Fail Function The DAC1054 powers up with the INT pin in a Low state To force this output high and reset this flag the CS pin will have to be brought low When this is done the INT output will be pulled high again via an external 10 kX pull-up resistor Any- ...
Page 12
Typical Applications FIGURE 7 Trimming the Offset Amp Whose Output is Biased FIGURE 8 Trimming the Offset of a Dual Supply Op Amp (V FIGURE 9 Bringing the Output Range Down to Ground ...
Page 13
... Physical Dimensions inches (millimeters) Order Number DAC1054CMJ 883 or 5962-9466201MJA NS Package Number J24A Order Number DAC1054CIWM NS Package Number M24B 13 ...
Page 14
... Fax (81-41) 35-1 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications Order Number DAC1054CIN NS Package Number N24A 2 A critical component is any component of a life ...