pca9549bs NXP Semiconductors, pca9549bs Datasheet
pca9549bs
Related parts for pca9549bs
pca9549bs Summary of contents
Page 1
PCA9549 Octal bus switch with individually I Rev. 01 — 11 July 2006 1. General description The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlled by the I with minimal propagation delay. Any individual ...
Page 2
... Philips Semiconductors 3. Ordering information Table 1. Type number PCA9549D PCA9549PW PCA9549BS 3.1 Ordering options Table 2. Type number PCA9549D PCA9549PW PCA9549BS 4. Block diagram RESET SCL SDA Fig 1. Block diagram PCA9549_1 Product data sheet Octal bus switch with individually I ...
Page 3
... PCA9549PW Fig 3. Pin configuration of TSSOP24 PCA9549BS 002aaa994 © Koninklijke Philips Electronics N.V. 2006. All rights reserved SDA 22 SCL ...
Page 4
Philips Semiconductors 5.2 Pin description Table 3. Symbol A0 A1 RESET SCL SDA V DD [1] HVQFN package die supply ground ...
Page 5
Philips Semiconductors 6. Functional description 6.1 Device addressing Following a START condition, the bus master must output the address of the slave it is accessing. The address of the PCA9549 is shown in internal pull-up resistors are incorporated on the ...
Page 6
Philips Semiconductors Table 4. Write = channel selection; read = channel status [1] Several bits can be enabled at the same time. For example ...
Page 7
Philips Semiconductors (1) maximum (2) typical (3) minimum Fig 7. V Figure 7 PCA9549 is only tested at the points specified in order for the PCA9549 to act as a voltage translator, the V or lower than the lowest bus ...
Page 8
Philips Semiconductors 7. Characteristics of the I 2 The I C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be ...
Page 9
Philips Semiconductors SDA SCL MASTER TRANSMITTER/ RECEIVER Fig 10. System configuration 7.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed ...
Page 10
Philips Semiconductors 7.4 Bus transactions Data is transmitted to the PCA9549 control register using the Write mode as shown in Figure 12. SDA Fig 12. Write control register Data is read from the PCA9549 using the Read mode as shown ...
Page 11
Philips Semiconductors 9. Static characteristics Table 6. Static characteristics See Table 7 on page 12 for Symbol Parameter ...
Page 12
Philips Semiconductors Table 7. Static characteristics See Table 6 on page 11 for Symbol Parameter Supply V supply ...
Page 13
Philips Semiconductors 10. Dynamic characteristics Table 8. Dynamic characteristics Symbol Parameter t propagation delay PD f SCL clock frequency SCL t bus free time between a STOP and BUF START condition t hold time (repeated) START condition HD;STA t LOW ...
Page 14
Philips Semiconductors SDA t BUF t LOW SCL t HD;STA P S Fig 14. Definition of timing on the I SCL SDA RESET 50 % Fig 15. Definition of RESET timing PCA9549_1 Product data sheet Octal bus switch with individually ...
Page 15
Philips Semiconductors 11. Application information C-bus/SMBus MASTER Remark: B can also be input and A can also be output as shown in bit 8. Fig 16. Typical application Fig 17. Custom multiplexer or ...
Page 16
Philips Semiconductors Fig 18. 2 channel 4-to-1 multiplexer or demultiplexer 12. Test information Fig 19. Test circuit PCA9549_1 Product data sheet Octal bus switch with individually PULSE GENERATOR C = load capacitance includes jig ...
Page 17
Philips Semiconductors 13. Package outline SO24: plastic small outline package; 24 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 18
Philips Semiconductors TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.15 0.95 mm ...
Page 19
Philips Semiconductors HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 0.85 mm terminal 1 index area terminal 1 24 index area DIMENSIONS (mm are ...
Page 20
Philips Semiconductors 14. Soldering 14.1 Introduction to soldering surface mount packages There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not ...
Page 21
Philips Semiconductors – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to ...
Page 22
Philips Semiconductors [3] These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 C body ...
Page 23
Philips Semiconductors 17. Legal information 17.1 Data sheet status [1][2] Document status Product status Objective [short] data sheet Development Preliminary [short] data sheet Qualification Product [short] data sheet Production [1] Please consult the most recently issued document before initiating or ...
Page 24
Philips Semiconductors 19. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . ...