max9394eti-t Maxim Integrated Products, Inc., max9394eti-t Datasheet
max9394eti-t
Related parts for max9394eti-t
max9394eti-t Summary of contents
Page 1
Rev 1; 5/07 2:1 Multiplexers and 1:2 Demultiplexers with General Description The MAX9394/MAX9395 consist of a 2:1 multiplexer and a 1:2 demultiplexer with loopback. The multiplexer section (channel B) accepts two low-voltage differential signaling (LVDS) inputs and generates a ...
Page 2
Multiplexers and 1:2 Demultiplexers with Loopback ABSOLUTE MAXIMUM RATINGS V to GND ...........................................................-0.3V to +4.1V CC IN_ _, OUT_ _, OUT_ _, EN_ _, _SEL, LB_SEL_ IN_ _, to GND........................................................-0. IN_ _ to IN_ _..........................................................................±3V Short-Circuit Duration ...
Page 3
Multiplexers and 1:2 Demultiplexers with DC ELECTRICAL CHARACTERISTICS (continued 3.0V to 3.6V 100Ω ±1%, EN_ (MAX9395 -40°C to +85°C, unless otherwise noted. Typical values are ...
Page 4
Multiplexers and 1:2 Demultiplexers with Loopback (V = 3.3V 0.2V +1.2V SUPPLY CURRENT vs. TEMPERATURE 3. 3. ...
Page 5
Multiplexers and 1:2 Demultiplexers with PIN NAME 30, N.C. No Connection. Not internally connected. 31 20, 25 GND Ground Channel B Output Enable. Drive ENB high to enable the LVDS outputs for channel ...
Page 6
Multiplexers and 1:2 Demultiplexers with Loopback PIN NAME Channel A0 Output Enable. Drive ENA0 high to enable the A0 LVDS outputs. An internal 435kΩ resistor 21 ENA0 to GND pulls ENA0 low when unconnected. Channel A0 LVDS Inverting Output. ...
Page 7
Multiplexers and 1:2 Demultiplexers with V IN_ IN_ _ t PLH V OUT_ OUT_ _ 80 ...
Page 8
Multiplexers and 1:2 Demultiplexers with Loopback IN_ _ IN_ _ GENERATOR V EN_ _ V WHEN V OUT_ _ V WHEN V OUT_ _ V WHEN V OUT_ _ V WHEN V OUT_ _ Figure 4. Output Active-to-Disable and ...
Page 9
Multiplexers and 1:2 Demultiplexers with Figure 6. Output Channel-to-Channel Skew Detailed Description The LVDS interface standard provides a signaling method for point-to-point communication over a con- trolled-impedance medium as defined by the ANSI TIA/EIA-644 standard. ...
Page 10
Multiplexers and 1:2 Demultiplexers with Loopback Table 1. Input Select Truth Table LOGIC INPUTS LB_SELA LB_SELB Don’t care. Differential Outputs The output common-mode ...
Page 11
Multiplexers and 1:2 Demultiplexers with INA INA LB_SELB OUTB OUTB ENB ______________________________________________________________________________________ LB_SELA ENA0 MAX9394 OUTA0 MAX9395 OUTA0 0 LB OUTA1 OUTA1 ENA1 INB0 0 LB INB0 0 INB1 1 INB1 BSEL Loopback Functional Diagram 11 ...
Page 12
Multiplexers and 1:2 Demultiplexers with Loopback Pin Configurations TOP VIEW N.C. 1 N.C. 2 N.C. 3 GND 4 MAX9394 ENB 5 MAX9395 OUTB 6 OUTB ...
Page 13
Multiplexers and 1:2 Demultiplexers with (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ Loopback Package Information PACKAGE OUTLINE, 32L TQFP, 5x5x1.0mm 1 21-0110 ...
Page 14
... Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2007 Maxim Integrated Products Package Information (continued) PACKAGE OUTLINE, 32L TQFP, 5x5x1.0mm 21-0110 is a registered trademark of Maxim Integrated Products, Inc ...