m29w400b-100za6tr STMicroelectronics, m29w400b-100za6tr Datasheet - Page 26
m29w400b-100za6tr
Manufacturer Part Number
m29w400b-100za6tr
Description
64 Mbit 8mb X8 Or 4mb X16, Multiple Bank, Boot Block 3v Supply Flash Memory
Manufacturer
STMicroelectronics
Datasheet
1.M29W400B-100ZA6TR.pdf
(74 pages)
- Current page: 26 of 74
- Download datasheet (557Kb)
Command interface
4.2.2
4.2.3
4.2.4
26/74
Quadruple Word Program command
This is used to write a page of four adjacent Words, in x16 mode, in parallel. The addresses
of the four Words must differ only in A1 and A0.
Five bus write cycles are necessary to issue the command.
1.
2.
3.
4.
5.
Double Byte Program
This is used to write two adjacent Bytes in x8 mode, in parallel. The addresses of the two
Bytes must differ only in DQ15A-1.
Three bus write cycles are necessary to issue the command.
1.
2.
3.
Quadruple Byte Program
This is used to write four adjacent Bytes in x8 mode, in parallel. The addresses of the four
Bytes must differ only in A0, DQ15A-1.
Five bus write cycles are necessary to issue the command.
1.
2.
3.
4.
5.
The first bus cycle sets up the command.
The second bus cycle latches the Address and the Data of the first Word to be written.
The third bus cycle latches the Address and the Data of the second Word to be written.
The fourth bus cycle latches the Address and the Data of the third Word to be written.
The fifth bus cycle latches the Address and the Data of the fourth Word to be written
and starts the Program/Erase Controller.
The first bus cycle sets up the command.
The second bus cycle latches the Address and the Data of the first Byte to be written.
The third bus cycle latches the Address and the Data of the second Byte to be written
and starts the Program/Erase Controller.
The first bus cycle sets up the command.
The second bus cycle latches the Address and the Data of the first Byte to be written.
The third bus cycle latches the Address and the Data of the second Byte to be written.
The fourth bus cycle latches the Address and the Data of the third Byte to be written.
The fifth bus cycle latches the Address and the Data of the fourth Byte to be written and
starts the Program/Erase Controller.
command
command
M29DW640F
Related parts for m29w400b-100za6tr
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
4 Mbit 512Kb x8 or 256Kb x16, Boot Block Low Voltage Single Supply Flash Memory
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
4 Mbit 512Kb x8 or 256Kb x16 / Boot Block Low Voltage Single Supply Flash Memory
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet: