tfa9842j-n1 NXP Semiconductors, tfa9842j-n1 Datasheet
tfa9842j-n1
Related parts for tfa9842j-n1
tfa9842j-n1 Summary of contents
Page 1
... The TFA9842J comes in a 9-pin DIL-bent-SIL (DBS9P) power package. The TFA9842J is pin compatible with the TFA9841J and TFA9843J. The TFA9842J contains a unique protection circuit that is solely based on multiple temperature measurements inside the chip. This gives maximum output power for all supply voltages and load conditions with no unnecessary audio holes. Almost any ...
Page 2
... stb P o THD G v SVRR 5. Ordering information Table 2: Type number TFA9842J DBS9P 9397 750 12013 Preliminary data 2-channel audio amplifi BTL) Quick reference data Conditions supply voltage operating no signal quiescent supply current standby supply current ...
Page 3
... MODE MUTE ON TFA9842J 5 GND IN2 1 OUT2 2 3 CIV IN1 4 TFA9842J GND 5 6 SVR 7 MODE OUT1 Rev. 01 — 26 April 2004 TFA9842J 8 OUT1 2 OUT2 SHORT-CIRCUIT AND TEMPERATURE PROTECTION SVR 0.5V CC MDB801 MDB802 © Koninklijke Philips Electronics N.V. 2004. All rights reserved ...
Page 4
... Power amplifier The power amplifi Single-Ended (SE) and/or Bridge-Tied Load (BTL) amplifier with an all-NPN output stage, capable of delivering a peak output current Using the TFA9842J as a BTL amplifier offers the following advantages: • 9397 750 12013 Preliminary data ...
Page 5
... Table 4: Headroom For the average listening level a power dissipation of 4.2 W can be used for a heatsink calculation. 8.3 Mode selection The TFA9842J has three functional modes, which can be selected by applying the proper DC voltage to pin MODE (see Table 5: V MODE 0 to 0 ...
Page 6
... This protects the TFA9842J against shorts to ground, to the supply voltage, across the load and too high chip temperatures. The protection will only be activated when necessary, so even during a short-circuit condition, a certain amount of (pulsed) current will still be fl ...
Page 7
... Figure 13; unless otherwise specified. Min Typ Max [ [ 100 - - 200 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. TFA9842J Unit 0 Unit K/W K/W Unit 3 ...
Page 8
... kHz ripple source = measured with an input voltage (RMS bandwidth from kHz, Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) Figure 12; unless otherwise specified. Min Typ Max 7 7.5 ...
Page 9
... V ( Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) mce486 (V) MODE THD = 10 %. ...
Page 10
... Preliminary data MDB809 (V) THD = BTL. MCE488 THD ( BTL. Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL ( kHz (%) 10 ...
Page 11
... Fig 9. Total power dissipation as function of channel output power per channel (worst case, both channels driven). 9397 750 12013 Preliminary data MCE489 (Hz) b. MCE507 (W) b. Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) 10 THD N (%) ...
Page 12
... Fig 11. Supply voltage ripple rejection as function of frequency. 9397 750 12013 Preliminary data MCE495 (Hz) b. MCE497 (Hz) = 300 mV (RMS); b. Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL (dB 100 BTL ...
Page 13
... CIV 3 V REF STANDBY MODE 7 MUTE SVR 6 TFA9842J GND Rev. 01 — 26 April 2004 TFA9842J 100 nF 8 OUT1 470 F OUT2 2 470 F SHORT-CIRCUIT AND TEMPERATURE PROTECTION V CC 0.5V CC mdb803 © Koninklijke Philips Electronics N.V. 2004. All rights reserved 1000 ...
Page 14
... SHORT-CIRCUIT 3 TEMPERATURE V REF PROTECTION V CC STANDBY 7 MUTE ON TFA9842J 5 GND Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) 100 nF 1000 F 8 OUT1 OUT2 AND 0. SVR 150 F MDB804 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. ...
Page 15
... 150 C (specification) j(max) is the total thermal resistance between the junction and the ambient including = (T T )/P th(tot) j(max) amb(max) D Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL TVA TFA9843J ...
Page 16
... C th(tot) = 90/4.2 = 21.4 K/W th(tot 21.4 th(h-a) th(tot) th(j-mb) MDB808 (V) b. Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) 2.0 = 8.7 K/W. 2.0 = 19.4 K/W. 150 100 External heatsink of 8 K/W; with music signals amb BTL. © ...
Page 17
... 14.7 3 12.4 11.4 3.5 2.54 1.27 5.08 14.3 2 11.0 10.0 REFERENCES JEDEC JEITA Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL view B: mounting base side ...
Page 18
... For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board. For PMFP packages hot bar soldering or manual soldering is suitable. Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) Soldering method Dipping Wave suitable ...
Page 19
... Revision history Table 12: Revision history Rev Date CPCN Description 01 20040426 - Preliminary data (9397 750 12013) 9397 750 12013 Preliminary data 2-channel audio amplifi BTL) Rev. 01 — 26 April 2004 TFA9842J © Koninklijke Philips Electronics N.V. 2004. All rights reserved ...
Page 20
... Rev. 01 — 26 April 2004 TFA9842J 2-channel audio amplifi BTL) © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Fax: + 24825 ...
Page 21
... Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 26 April 2004 Document order number: 9397 750 12013 TFA9842J 2-channel audio amplifi BTL) ...