tn87c196kd20 ETC-unknow, tn87c196kd20 Datasheet
tn87c196kd20
Available stocks
Related parts for tn87c196kd20
tn87c196kd20 Summary of contents
Page 1
...
Page 2
...
Page 3
VERTICAL WINDOWING MAP Table 1. 128-Byte Windows Address to Device WSR Contents Remap Series 0380H KD X001 0111B 0300H KD X001 0110B 0280H KD X001 0101B 0200H KD X001 0100B 0180H KC, KD X001 0011B 0100H KC, KD X001 ...
Page 4
PROCESS INFORMATION This device is manufactured on PX29.5 or PX29.9, a CHMOS III process. Additional process and reliabili- ty information is available in the Intel® Quality System Handbook: http://developer.intel.com/design/quality/quality.htm NOTE: 1. EPROMs are available as One ...
Page 5
Figure 4. 68-Pin PLCC Package 8XC196KD/8XC196KD20 272145 – ...
Page 6
NOTE: N.C. means No Connect (do not connect these pins). 6 Figure 5. 80-Pin QFP Package 272145– 4 ...
Page 7
NOTE: N.C. means No Connect (do not connect these pins). Figure 6. 80-Pin SQFP Package 8XC196KD/8XC196KD20 272145– ...
Page 8
PIN DESCRIPTIONS Symbol V Main supply voltage (5V Digital circuit ground (0V). There are multiple Reference voltage for the A/D converter (5V). V REF portion of the A/D converter and the logic used to ...
Page 9
PIN DESCRIPTIONS (Continued) Symbol Port 0 8-bit high impedance input-only port. These pins can be used as digital inputs and/or as analog inputs to the on-chip A/D converter. Port 1 8-bit quasi-bidirectional I/O port. Port 2 8-bit multi-functional port. All ...
Page 10
ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Ambient Temperature Under Bias................................. Storage Temperature.................... Voltage On Any Pin Except EA and V 0.5V to ................... PP b Voltage from EA or ...
Page 11
DC CHARACTERISTICS (Over Specified Operating Conditions) (Continued) Symbol Description I Logical 1 Output Current in Reset OH1 on P2.0. Do not exceed this or device may enter test modes. I Logical 0 Input Current in Reset IL2 on P2.0. Maximum ...
Page 12
I Max 4.13 Frequency Typ 3.50 Frequency Max 1.25 Frequency 5 mA IDLE Typ 0.88 Frequency 3 mA IDLE e a ...
Page 13
AC CHARACTERISTICS (Continued) For use over specified operating conditions. Test Conditions: Capacitive load on all pins The 80C196KD will meet these specifications: Symbol Description F Frequency on XTAL1 (8XC196KD) XTAL F Frequency on XTAL1 (8XC196KD20) XTAL T I/F (8XC196KD) OSC ...
Page 14
System Bus Timings 14 272145 ±6 ...
Page 15
READY Timings (One Wait State) Buswidth Timings 8XC196KD/8XC196KD20 272145 ±7 272145 ±8 15 ...
Page 16
HOLD/HLDA TIMINGS Symbol Description T HOLD Setup HVCH T CLKOUT Low to HLDA Low CLHAL T CLKOUT Low to BREQ Low CLBRL T HLDA Low to Address Float HALAZ T HLDA Low to BHE, INST, RD, WR Weakly Driven ...
Page 17
MAXIMUM HOLD LATENCY Bus Cycle Type Internal Execution 1.5 States 16-Bit External Execution 2.5 States 8-Bit External Execution 4.5 States EXTERNAL CLOCK DRIVE (8XC196KD) Symbol Parameter 1/T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low ...
Page 18
EXTERNAL CRYSTAL CONNECTIONS NOTE: Keep oscillator components close to chip and use short, direct traces to XTAL1, XTAL2 and V using ceramic crystals pF When using ceramic resonators consult manufacturer for recommended capacitor values. AC ...
Page 19
AC CHARACTERISTICS-SERIAL PORT-SHIFT REGISTER MODE SERIAL PORT TIMING-SHIFT REGISTER MODE (MODE0) Symbol Parameter T Serial Port Clock Period (BRR XLXL T Serial Port Clock Falling Edge XLXH to Rising Edge (BRR t T Serial Port Clock Period (BRR XLXL T ...
Page 20
CHARACTERISTICS The A/D converter is ratiometric, so absolute accuracy is dependent on the accuracy and stability of V 10-BIT MODE A/D OPERATING CONDITIONS Symbol Description T Ambient Temperature Commercial Temp Ambient Temperature Extended Temp. ...
Page 21
MODE A/D OPERATING CONDITIONS Symbol Description T Ambient Temperature Commercial Temp Ambient Temperature Extended Temp Digital Supply Voltage CC V Analog Supply Voltage REF ANGND Analog Ground Voltage T Sample Time SAM T Conversion Time ...
Page 22
OTPROM SPECIFICATIONS OPERATING CONDITIONS Symbol Description T Ambient Temperature During Programming A V Supply Voltage During Programming CC V Reference Supply Voltage During Programming REF V Programming Voltage Pin Voltage EA F Oscillator Frequency during Auto ...
Page 23
DC OTPROM PROGRAMMING CHARACTERISTICS Symbol Description I V Supply Current (When Programming NOTE: Do not apply V until V is stable and within specifications and the oscillator/clock has stabilized or the device may damaged. OTPROM ...
Page 24
SLAVE PROGRAMMING MODE IN WORD DUMP WITH AUTO INCREMENT NOTE: P3.0 must be low (``0'') SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM WITH REPEATED PROG PULSE AND AUTO INCREMENT 24 272145 ±17 272145 ±18 ...
Page 25
... The following are important differences between the 272145-004 and 272145-005 datasheets: 1. Package prefix variables have been changed. Variables are now indicated with an "x". The following are important differences between the 272145-002 and 272145-003 data sheets: 1 ...