isl6236 Intersil Corporation, isl6236 Datasheet - Page 33

• Manufacturer Part Number: isl6236
• Description: High-efficiency, Quad-output, Main Power Supply Controllers For Notebook Computers
• Manufacturer: Intersil Corporation

Input Capacitor Selection
The input capacitors must meet the input-ripple-current
(I
ISL6236 dual switching regulator operates at different
frequencies. This interleaves the current pulses drawn by
the two switches and reduces the overlap time where they
add together. The input RMS current is much smaller in
comparison than with both SMPSs operating in phase. The
input RMS current varies with load and the input voltage.
The maximum input capacitor RMS current for a single
SMPS is given by:
When
current of
The ESR of the input-capacitor is important for determining
capacitor power dissipation. All the power (I
heats up the capacitor and reduces efficiency. Nontantalum
chemistries (ceramic or OS-CON) are preferred due to their
low ESR and resilience to power-up surge currents. Choose
input capacitors that exhibit less than +10°C temperature
rise at the RMS input current for optimal circuit longevity.
Place the drains of the high-side switches close to each
other to share common input bypass capacitors.
Power MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability (>5A)
when using high-voltage (>20V) AC adapters. Low-current
applications usually require less attention.
Choose a high-side MOSFET (Q1/Q3) that has conduction
losses equal to the switching losses at the typical battery
voltage for maximum efficiency. Ensure that the conduction
losses at the minimum input voltage do not exceed the
package thermal limits or violate the overall thermal budget.
Ensure that conduction losses plus switching losses at the
maximum input voltage do not exceed the package ratings
or violate the overall thermal budget.
Choose a synchronous rectifier (Q2/Q4) with the lowest
possible r
high-side switch turning on due to parasitic drain-to-gate
capacitance, causing cross-conduction problems. Switching
losses are not an issue for the synchronous rectifier in the
buck topology since it is a zero-voltage switched device
when using the buck topology.
MOSFET Power Dissipation
Worst-case conduction losses occur at the duty-factor
extremes. For the high-side MOSFET, the worst-case power
dissipation (PD) due to the MOSFET's r
minimum battery voltage:
I
RMS
RMS
≈
) requirement imposed by the switching current. The
V
I
LOAD
IN
DS(ON)
I
=
LOAD
⎛
⎜
⎝
2 V
------------------------------------------------------------
⋅
V
2 ⁄
. Ensure the gate is not pulled up by the
OUT
OUT_
.
(
V
(
V
IN
D
IN
=
–
50%
V
OUT_
33
)
, IRMS has maximum
)
⎞
⎟
⎠
DS(ON)
RMS
occurs at the
2
x ESR)
(EQ. 18)
ISL6236
Generally, a small high-side MOSFET reduces switching
losses at high input voltage. However, the r
to stay within package power-dissipation limits often limits
how small the MOSFET can be. The optimum situation
occurs when the switching (AC) losses equal the conduction
(r
Switching losses in the high-side MOSFET can become an
insidious heat problem when maximum battery voltage is
applied, due to the squared term in the CV
equation. Reconsider the high-side MOSFET chosen for
adequate r
extraordinarily hot when subjected to V
Calculating the power dissipation in NH (Q1/Q3) due to
switching losses is difficult since it must allow for quantifying
factors that influence the turn-on and turn-off times. These
factors include the internal gate resistance, gate charge,
threshold voltage, source inductance, and PC board layout
characteristics. The following switching-loss calculation
provides only a very rough estimate and is no substitute for
bench evaluation, preferably including verification using a
thermocouple mounted on NH (Q1/Q3):
where C
(Q1/Q3) and I
current.
For the synchronous rectifier, the worst-case power
dissipation always occurs at maximum battery voltage:
The absolute worst case for MOSFET power dissipation
occurs under heavy overloads that are greater than
I
current limit and cause the fault latch to trip. To protect
against this possibility, "overdesign" the circuit to tolerate:
where I
by the current-limit circuit, including threshold tolerance and
resistance variation.
Rectifier Selection
Current circulates from ground to the junction of both
MOSFETs and the inductor when the high-side switch is off.
As a consequence, the polarity of the switching node is
negative with respect to ground. This voltage is
approximately -0.7V (a diode drop) at both transition edges
PD Q
PD Q
PD Q
LOAD(MAX)
I
LOAD
DS(ON)
(
(
(
H
H
L
)
=
LIMIT(HIGH)
Resistance
Switching
RSS
) losses.
=
I
LIMIT HIGH
DS(ON)
⎛
⎜
⎝
1
but are not quite high enough to exceed the
is the reverse transfer capacitance of Q
–
GATE
------------------------- -
V
(
IN MAX
V
)
)
OUT
(
at low battery voltages if it becomes
=
is the maximum valley current allowed
is the peak gate-drive source/sink
=
)
⎛
⎜
⎝
(
+
------------------------
V
V
V
)
(
IN MIN
⎞
⎟
⎠
IN MAX
(
OUT_
I
LIR
LOAD
(
(
) 2 ⁄
)
⎞
⎟
⎠
2
)
) I
(
)
⋅
I
2
⋅
LOAD
r
⎛
⎜
⎝
DS ON
LOAD MAX
C
---------------------------------------------------- -
RSS
(
)
IN(MAX)
2
(
)
⋅
I
⋅
GATE
f
r
SW
2
DS ON
DS(ON)
f switching-loss
)
(
⋅
.
I
LOAD
)
June 28, 2007
required
⎞
⎟
⎠
H
(EQ. 21)
(EQ. 22)
(EQ. 19)
(EQ. 20)
FN6373.3