a152-db-5 Teledyne Technologies Incorporated., a152-db-5 Datasheet - Page 2

• Manufacturer Part Number: a152-db-5
• Description: Series Designation A152 Relay Type Attenuator Relay Series
• Manufacturer: Teledyne Technologies Incorporated.

SERIES A152
GENERAL PERFORMANCE (–55°C to + 85°C, unless otherwise specified)
A152 Page 2
ELECTRICAL SPECIFICATION (–55°C to +85°C, unless otherwise specified)
PARAMETER
Operating Frequency (Note 2)
Power (Notes 5 and 6)
Impedance
Contact life rating
PART NUMBER (Note 7)
Coil Voltage Vdc (Note 6)
Coil Resistance Ohms ±20%
Pick-up Voltage Vdc Max.
Switching Time ms (Note 8)
Insulation Resistance
Dielectric Strength
PARAMETER
OUTLINE DIMENSIONS
(
Dimensions are show in inches (millimeters).
Terminal numbers shown are for reference only.
Leads 1 and 7 are grounded to the case.
.187" lead lengths available (see part numbering system)
.017
.43
+.002
–.001
+.05
–.03
)
DIA.
.031 REF.
CASE DETAIL
(.79)
.335 MAX.
(8.51)
2
1
3
.375 MAX.
(9.53)
6
7
5
.700 MIN.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
(17.78)
(7.49)
.295
.150 ±.10 TYP.
(5.08 ±5.08)
(3.81 ±.25)
.200 ±.01
Nom.
Max.
@25°C
@25°C
Max.
Typ.
.035 REF.
(.89)
MINIMUM
.435 MAX.
.475 MAX.
0.0
(11.05)
(12.07)
A152-dB-5
5.8
3.8
50
5
1,000 M
TYPICAL
GENERAL NOTES
1. Contacts will exhibit no contact chatter in excess of
2. Relays may be operated at higher frequencies with
3. For optimal RF performance, solder case to RF ground
4. Attenuation values shown are with reference to the
5. Power handling for case temperatures of –55°C to
6. Do not operate coil at maximum coil voltage
7. Insert attenuation value, see part numbering system.
8. Switching time includes bounce.
9. The slash and characters appearing after the slash are
10. Unless otherwise specified, relays will be supplied with
300 VRMS / 60 Hz typical (at sea level)
Designator
*Contact factory for additional
attenuation values
TELEDYNE RELAYS PART NUMBERING SYSTEM
FOR A152 ATTENUATOR RELAYS
50
10 μs or transfer in excess of 1 μs.
reduced RF performance.
plane.
through path (low loss state).
+55°C is 1 Watt. Derate power handling 25 mW/°C
above +55°C. Case measurement point is adjacent to
the relay tab.
continuously.
not marked on the relay.
either gold-plated or solder-coated leads.
Series
A152-dB-12
Typical at low level
typical (all mutually isolated points)
10,000,000 cycles
16.0
390
9.0
12
A152
Attenuation
Value (dB)
–
4.0
2.0
MAXIMUM
Coil Voltage
20*
Nominal
5.0
A152-dB-15
1.0
20.0
11.3
610
–
15
XX
© 2006 TELEDYNE RELAYS
S=.187" Leads
See Note 9
Q=Solder-Coated Leads
G=Gold-Plated Leads
/
(Notes 9 & 10)
S
A152-dB-26
UNITS
Ohms
Q
GHz
Watt
1560
26.5
32.0
18.0
A152\042006\Q1