FS6011-02 AMI, FS6011-02 Datasheet - Page 14

• Manufacturer Part Number: FS6011-02
• Description: DIGITAL AUDIO/VIDEO CLOCK GENERATOR IC
• Manufacturer: AMI

www.DataSheet4U.com
8.1
8.2
8.3
1. At the appropriate disk drive prompt (A:\) type Install
2. Connect a +5 Volt power supply to the board: RED =
3. Remove all software keys from the computer parallel
4. Connect the supplied interface cable to the parallel
5. Connect the clock outputs to the target application
8.4
1. Type FS6011 at the C:\FS6011 prompt to run the
Demonstration board
Interface cable (DB25 to 6-pin connector)
Data sheet
Demonstration software, including:
PC running MS-DOS or MS Windows 3.1x, with ac-
cessible parallel (LPT1) port
MS-QBasic v. 1.1 or later (or equivalent software)
6.3kB available space on drive C:
to automatically copy demo files to the C: drive.
NOTE: This demo software requires Microsoft QBa-
sic or equivalent to run. Make sure the directory
containing qbasic.exe is in the DOS path statement,
or move the demo files to a directory containing Ba-
sic.
+5V, BLACK = ground.
port.
port (DB25 connector) and to the demo board (6-pin
connector). Make sure the cable is facing away from
the board – pin 1 is the red wire.
board with a twisted-pair cable.
Qbasic-based demo program.
INSTALL.BAT
FS6011.BAT
FS6011G.BAS
tion Instructions
Contents
Requirements
Board Setup and Software Installa-
Demo Program
0.75kB
0.24kB
5.3kB
14
2. The following banner should appear:
3. After pressing any key, a menu should appear con-
Refer to Table 18 for a description of each hot key.
4. To change the frequency of the desired clock, press
5. Refer (in the FS6011 data sheet) to Table 3 and
6. Observe the response to the hot key selection. Re-
7. Pressing a hot key strobes a 15-bit message to the
Note that the PCLK frequency is changed by directly ad-
dressing pins 4 and 5 (PSEL0 and PSEL1) of the device.
Therefore the hot key response message will be un-
changed when selecting the (P)CLK hot key. Press X to
exit the demo program.
Writing...
(0x000) Binary: LSB 000000000000000 MSB
****************************************
*
*
*
*
*
****************************************
taining a list of the program hot keys, a message that
the computer parallel (LPT1) port was found, and the
address at which the port was found.
the appropriate hot key. The keys are not case sensi-
tive.
Table 4 for ACLK frequencies, Table 5 for UCLK fre-
quencies, and Table 6 for PCLK frequencies.
peated pressing of the same key will scroll through
the entire range of frequencies for the selected clock,
returning to the initial frequency.
demo board via the interface cable. The response to
the key selection is shown below:
where the numbers are the data in hex and binary.
PRESS ANY KEY TO CONTINUE.....
***********************
* FS6011 Pgm. Utility *
*
* chip (R)efresh
* chip (I)nitialize
* (A)clk
* a(O)ffset
* (C)lk27
* (U)clk
* (V)cxo
* vcxo (E)nable
* (P)clk
* e(X)it
***********************
FS6011 Utility Program
=
=
=
=
=
=
=
0 *
0 *
0 *
0 *
0 *
0 *
0 *
*
*
*
*
July 1998
7.20.98
*
*
*
*
*