LTC1343 Linear Technology, LTC1343 Datasheet - Page 11

no-image

LTC1343

Manufacturer Part Number
LTC1343
Description
Software-Selectable Multiprotocol Transceiver
Manufacturer
Linear Technology
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC1343CGW
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1343CGW#PBF
Manufacturer:
LTC
Quantity:
270
Part Number:
LTC1343CGW#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1343IGW
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1343IGW#PBF
Manufacturer:
LTC
Quantity:
532
Part Number:
LTC1343IGW#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1343IGW#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS
has a unique data latch signal which acts as a write enable.
When the LATCH pin is low the buffers on the M0, M1, M2,
CTRL/CLK, DCE/DTE, LB and EC pins are transparent.
When the LATCH pin is pulled high the buffers latch the
data and changes on the input pins will no longer affect
the chip.
The mode selection may also be accomplished by using
jumpers to connect the mode pins to ground or V
Cable Termination
Traditional implementations have included switching re-
sistors with expensive relays, or requiring the user to
change termination modules every time the interface
standard has changed. Custom cables have been used
with the termination in the cable head, or separate termi-
nations are built on the board and a custom cable routes
the signals to the appropriate termination. Switching the
terminations with FETs is difficult because the FETs must
CONTROLLER
DCE/DTE
LATCH 1
LATCH 2
LATCH 3
Figure 12: Mode Selection by the Controller
M0
M1
M2
U
INFORMATION
U
M0
M1
M2
DCE/DTE
LATCH
M0
M1
M2
DCE/DTE
LATCH
M0
M1
M2
DCE/DTE
LATCH
W
PORT #1
PORT #2
PORT #3
U
CC
.
1343 F12
remain off even though the signal voltage is beyond the
supply voltage for the FET drivers or the power is off.
Using the LTC1344 along with the LTC1343 solves the
cable termination switching problem. Via software con-
trol, the LTC1344 provides termination for the V.10
(RS423), V.11 (RS422), V.28 (RS232) and V.35 electrical
protocols.
V.10 (RS423) Interface
A typical V.10 unbalanced interface is shown in Figure 13.
A V.10 single-ended generator output A with ground C is
connected to a differential receiver with inputs A
nected to A, and input B
ground C. The receiver’s ground C
signal return. Usually, no cable termination is required for
V.10 interfaces, but the receiver inputs must be compliant
with the impedance curve shown in Figure 14.
–3.25mA
GENERATOR
–10V
Figure 14. V.10 Receiver Input Impedance
Figure 13. Typical V.10 Interface
A
C
INTERCONNECTING
BALANCED
–3V
CABLE
'
connected to the signal return
I
Z
A
B
C
TERMINATION
'
'
'
3V
'
CABLE
is separate from the
LTC1343
LOAD
RECEIVER
10V
11
1343 F14
1343 F13
'
V
3.25mA
con-
Z

Related parts for LTC1343