CLAA215FA01 CHUNGHWA PICTURE TUBES, CLAA215FA01 Datasheet

Page 1

... GATHER Date : 2008/12/30 CPT TFT-LCD CLAA 215FA01 ACCEPTED BY ： APPROVED BY Joe Chou CHUNGHWA PICTUER TUBES, LTD. No. 1, Huaying Rd., Sanho Tsun, Lungtan Shiang, Taoyuan, Taiwan, 325, R.O.C. Doc. No: CLAA215FA01-GATHER-SPEC ...

Page 2

... Title：CLAA215FA01 NO 1 OVERVIEW 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL CHARACTERISTICS 4 INTERFACE PIN CONNECTION 5 INTERFACE TIMING 6 BLOCK DIAGRAM 7 MECHANICAL SPECIFICATION 8 OPTICAL CHARACTERISTICS 9 RELIABILITY TEST CONDITIONS 10 DESIGNATION OF LOT MARK 11 PACKING SPECIFICATION 12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. ...

Page 3

... Title：CLAA215FA01 1. OVERVIEW CLAA215FA01 is 21.5” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit and backlight. By applying 6 bit digital data, 1920×1080, 16.7M-color images are displayed on the 21.5” diagonal screen. Input power voltage is 5.0V for LCD driving ...

Page 4

... Title：CLAA215FA01 2. ABSOLUTE MAXIMUM RATINGS ITEM Power Supply Voltage for LCD Lamp Voltage Lamp Current Lamp Frequency static electricity Operation Temperature Storage Temperature Delayed Discharge Time [Note] 1).The relative temperature and humidity range are as below sketch, 90%RHMax.(Ta≦40℃). 2).The maximum wet bulb temperature 3) ...

Page 5

... Title：CLAA215FA01 Relative humidity(%RH ELECTRICAL CHARACTERISTICS (1).TFT-LCD ITEM Power Supply Voltage for LCD Power Supply Current for LCD Permissive Ripple Voltage for Logic Differential Resistance The same motion input Voltage Differential input Voltage LVDS: IN+，IN- High electric potential threshold ...

Page 6

... Title：CLAA215FA01 [Note] *1)Power、data sequence 0.50ms≦t1≦10ms 0.01ms＜t2≦50ms 0.01ms＜t3≦50ms LCD Power Supply Logic Signal Backlight Power Supply VCC-dip conditions: (1) When 3.6V≦Vcc(min)<4.5V: td≦10 ms (2) When Vcc <3.6 V, VCC-dip conditions should also follow the VCC-turn-on conditions. 2). ...

Page 7

... Title：CLAA215FA01 3) LVDS Signal definition * VIN+：Positive differential DATA & CLK Input VIN-： Negative differential DATA ＆ CLK Input *4).Irush Measurement Condition ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification CHUNGHWA PICTUER TUBES, LTD. ...

Page 8

... Title：CLAA215FA01 (2).Backlight 1. Electrical specification ITEM B/L Voltage B/L Current B/L operating current B/L power consumption Inverter Frequency Starting Lamp Voltage 2. Lamp life time ITEM Lamp life time Rated time (turn on/off) [Note] Inverter vendor: Sumida, model: TWS-400-9656 1) If the waveform of light up-driving is asymmetric, the distribution of mercury inside the lamp tube will become unequally or will deplete the Ar gas in it ...

Page 9

... Title：CLAA215FA01 3) Lamp Current measurement method (The current meter is inserted in cold line) LCD Module 4) a. Frequency in this range can make the characteristics of electric and optics maintain in +/- 10% except color coordinates. b. Frequency in 50~60kHz can make characteristics of electric and optics better. c. Frequency in 45~80kHz won’t damage the lifetime and reliability of lamp. ...

Page 10

... Title：CLAA215FA01 9) The Starting Lamp Voltage (VS) of inverter must be driven large than one second. 10) The output voltage of inverter (Vn) must be the same phase of between any lamps. 11) The difference in voltage between any lamps ( V) must be smalle Example： ∣△ ∣＜300V， − ...

Page 11

... Title：CLAA215FA01 4. INTERFACE PIN CONNECTION (1) CN1 Outlet connector: GS2330-0312R-7F (FOXCONN) (or equivalent) PIN NO. REMARK 1 RXO0- 2 RXO0+ 3 RXO1- 4 RXO1+ 5 RXO2- 6 RXO2+ 7 GND 8 RXOC- 9 RXOC+ 10 RXO3- 11 RXO3+ 12 RXE0- 13 RXE0+ 14 GND 15 RXE1- 16 RXE1+ 17 GND 18 RXE2- 19 RXE2+ 20 RXEC- 21 RXEC+ 22 RXE3- 23 RXE3+ 24 GND VCC ...

Page 12

... Title：CLAA215FA01 No. CN2 CN3 CN4 CN5 ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification Pin Symbol 1 HV High Voltage Output for CCFL Lamp Low Voltage Output for CCFL Lamp High Voltage Output for CCFL Lamp 2 ...

Page 13

... Title：CLAA215FA01 5. INTERFACE TIMING (1) Timing Characteristic DCLK Horizontal LCD Timing DENA [Note] *1) DENA (data enable) usually is positive *2) DCLK still inputs during blanking *3) LVDS transmitter IC: NT71679-00024(NVT) *4) DE mode only *5) It maybe cause flicker at 50Hz. (2).Timing Chart a. Horizontal Signal DCLK ODD DATA ...

Page 14

... Title：CLAA215FA01 b. Vertical Signal LINE DATA DENA (3).LVDS Data For 6Bit+Hi-FRC RXOC RXO4 RXO3 RXO2 RXO1 RXEC RXE4 RXE3 RXE2 RXE1 ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification Invalid Data ...

Page 15

... Title：CLAA215FA01 Color Data Assignment COLOR INPUT DATA MSB BLACK 0 RED(255) 1 GREEN(255) 0 BASIC BLUE(255) 0 COLOR CYAN 0 MAGENTA 1 YELLOW 1 WHITE 1 RED(0) 0 RED(1) 0 RED(2) 0 RED RED(254) 1 RED(255) 1 GREEN(0) 0 GREEN(1) 0 GREEN(2) ...

Page 16

... Title：CLAA215FA01 6. BLOCK DIAGRAM TFT-LCD Module LVDS receiver 2ch Timing Controller Power Supply Circuit Lamp Uint in Backlight ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification Lamp Unit in Backlight Source Driver LCD Panel 1920 1080 ...

Page 17

... Title：CLAA215FA01 7. MECHANICAL SPECIFICATION (1) Front side (Tolerance is ± 0.5mm unless noted) ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification CHUNGHWA PICTUER TUBES, LTD. Doc. No： Version： A Issue Date ： 2008/12/30 [Unit:mm] 17/31 Page: Datasheet pdf - http://www.DataSheet4U.net/ ...

Page 18

... Title：CLAA215FA01 (2) Rear side (Tolerance is ±0.5mm unless noted) ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification CHUNGHWA PICTUER TUBES, LTD. Doc. No： Version： A Issue Date ： ...

Page 19

... Title：CLAA215FA01 8. OPTICAL CHARACTERISTICS ITEM Contrast (CEN) Luminance (CEN) 9P Uniformity Response Time Cross talk Horizontal Vertical View angle Horizontal Vertical White Red Color Coordinates Green Blue Gamut Gamma [Note] Color coordinate and color gamut are measured by SRUL1R, response time is measured by TRD-100, and all the other items are measured by BM-5A (TOPCON) ...

Page 20

... Title：CLAA215FA01 2) Definition of Contrast Ratio CR=ON (White) Luminance/OFF (Black) Luminance 3) Definition of Luminance and Luminance uniformity Central luminance: The white luminance is measured at the center position “5” on the screen, see Fig.1 below. And the measure time is 30 min after discharged. 9P Luminance (AVG): The white luminance is measured at measuring points see Fig.1 below. 9P Uniformity: ∆ ...

Page 21

... Title：CLAA215FA01 4).Definition of Viewing Angle (θ,ψ): 5) Definition of Response Time: 6) Definition of crosstalk: CT ∣ ∣ The luminance of measured position at pattern The luminance of measured position at pattern B with Gray level ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. ...

Page 22

... Title：CLAA215FA01 7) Definition of Gamma (γ), follow VESA standard sampling every 16 gray level (0,16,32,…..224,240,255) 9. RELIABILITY TEST CONDITIONS (1) Temperature and Humidity TEST ITEMS HIGH TEMPERATURE HIGH HUMIDITY OPERATION HIGH TEMPERATURE HIGH HUMIDITY STORAGE HIGH TEMPERATURE OPERATION 50 ; 240h HIGH TEMPERATURE STORAGE LOW TEMPERATURE OPERATION ...

Page 23

... Title：CLAA215FA01 (3) ESD POSITION Connector Module (4) Low Pressure test TEST ITEM Low Pressure test(storage) (5) Judgment standard The judgment of the above test should be made as follow: Pass: Normal display image with no obvious non-uniformity and no line defect. Partial transformation of the module parts should be ignored. ...

Page 24

... Title：CLAA215FA01 10. DESIGNATION OF LOT MARK (c) (a) NEW 3_IN_1 LABEL: (Model Name: CLAA215FA01) A A：Year B、C：Week D、E、F、G、H：Serial No. I：Factory Code ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. TECHNICAL SPECIFICATION Technical Specification (b) ( CHUNGHWA PICTUER TUBES, LTD ...

Page 25

... Title：CLAA215FA01 [Note] (1) Year Year 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 Mark (2) Week Week Mark (3) Serial No. Serial No. Mark (4) Factory Code Factory T2 Code Factory Mark R (b) PANEL LABEL： (c) B/L MAKER LABEL： ( R215FA01xxxxxxxxxxxxxxxxxxx) R215FA01xxxxxxxxxxxxxxxxxxx (2) Location of Lot Mark The label is attached to the backside of the LCD Module ...

Page 26

... Title：CLAA215FA01 11. PACKING SPECIFICATION (1)Packing 7 LCD IT modules (max Box 24 box (max pallet Box dimensions: 570(L)×244(W)×370(H) Weight: approximately 20.4Kg (7 modules per box) (2)Packing Method Figure (a) and (b) are the packing method 215” ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. ...

Page 27

... Title：CLAA215FA01 Cover Protector: L1090 × 50 × 50mm Pallet: 1150(L) × 1000(W) × 130(H) mm Top/Bottom Cap: L1150 × 1000 × 130mm Pallet stack: 1150(L) × 1000(W) × 1260(H) mm Gross Weight: 500Kg (±2Kg) ISO Datasheet No: T-3010004-008-F Datasheet Version.: 01 CHUNGHWA PICTUER TUBES, LTD. ...

Page 28

... Title：CLAA215FA01 12. HANDLING PRECAUTIONS FOR TFT-LCD MODULE Please pay attention to the followings in handling- TFT-LCD products; 1. ASSEMBLY PRECAUTION (1) Please use the mounting hole on the module side in installing and do not beading or wrenching LCD in assembling. And please do not drop, bend or twist LCD module in handling. ...

Page 29

... Title：CLAA215FA01 (9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting wit inverter. 2. OPERATING PRECAUTIONS (1) Please be sure to turn off the power supply before connecting and disconnecting signal input cable. (2) Please do not change variable resistance settings in LCD module. They are adjusted to the most suitable value ...

Page 30

... Title：CLAA215FA01 (2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off thoroughly with soap and water. 6. OTHERS (1) A strong incident light into LCD panel might cause display characteristics' changing inferior because of polarizer film, color filter, and other materials becoming inferior. Please do not expose LCD module direct sunlight Land strong UV rays ...