AD8197 Analog Devices, AD8197 Datasheet - Page 29

no-image

AD8197

Manufacturer Part Number
AD8197
Description
4:1 HDMI/DVI Switch with Equalization
Manufacturer
Analog Devices
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD8197AASTZ
Manufacturer:
ADI
Quantity:
246
Part Number:
AD8197AASTZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD8197AASTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD8197AASTZ-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD8197ASTZ
Manufacturer:
ADI
Quantity:
181
Part Number:
AD8197ASTZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD8197ASTZ
Quantity:
20
Part Number:
AD8197ASTZ-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD8197B
Manufacturer:
ADI
Quantity:
624
Part Number:
AD8197BASTZ
Manufacturer:
AD
Quantity:
1 831
Part Number:
AD8197BASTZ
Manufacturer:
ADI
Quantity:
186
Part Number:
AD8197BASTZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD8197BASTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Preliminary Data Sheet
Power Supplies
The AD8197 has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are:
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8197. The VTTI/AVEE supply (3.3 V)
powers the input termination (see Figure 25). Similarly, the
VTTO/AVEE supply (3.3 V) powers the output termination
(see Figure 26). The AMUXVCC/DVEE supply (3.3 V to 5 V)
powers the auxiliary multiplexer core and determines the
maximum allowed voltage on the auxiliary lines. For example,
if the DDC bus is using 5 V I
connected to +5 V relative to DVEE.
In a typical application, all pins labeled AVEE or DVEE should
be connected directly to ground. All pins labeled AVCC,
DVCC, VTTI, or VTTO should be connected to 3.3 V, and
Pin AMUXVCC tied to 5 V. The supplies can also be powered
individually, but care must be taken to ensure that each stage of
the AD8197 is powered correctly.
Power Supply Bypassing
The AD8197 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground to filter out supply noise. Generally, bypass
capacitors should be placed near the power pins and should
connect directly to the relevant supplies (without long inter-
vening traces). For example, to improve the parasitic inductance
of the power supply decoupling capacitors, minimize the trace
length between capacitor landing pads and the vias as shown in
Figure 34.
AVCC/AVEE
VTTI/AVEE
VTTO/AVEE
DVCC/DVEE
AMUXVCC/DVEE
2
C, then AMUXVCC should be
PrA | Page 29 of 32
In applications where the AD8197 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. The capacitors should via down directly to the
supply planes and be placed within a few centimeters of the
AD8197. The AMUXVCC supply does not require additional
bypassing. This bypassing scheme is illustrated in Figure 35.
Figure 35. Example Placement of Power Supply Decoupling Capacitors
Figure 34. Recommended Pad Outline for Bypass Capacitors
Around the AD8197
RECOMMENDED
NOT RECOMMENDED
EXTRA ADDED INDUCTANCE
AD8197

Related parts for AD8197