BTS426L1E3043 Infineon Technologies AG, BTS426L1E3043 Datasheet
![no-image](/images/manufacturer_photos/0/3/328/infineon_technologies_ag_sml.jpg)
BTS426L1E3043
Related parts for BTS426L1E3043
BTS426L1E3043 Summary of contents
Page 1
Smart Highside Power Switch Features Overload protection Current limitation Short circuit protection Thermal shutdown Overvoltage protection (including load dump) Fast demagnetization of inductive loads 1 ) Reverse battery protection Undervoltage and overvoltage shutdown with auto-restart and hysteresis Open drain diagnostic ...
Page 2
Pin Symbol 1 GND - OUT O (Load, L) Maximum Ratings °C unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 3) Supply ...
Page 3
Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (pin Nominal load current, ISO Norm ...
Page 4
Parameter and Conditions ° unless otherwise specified j bb Protection Functions 9) Initial peak short circuit current limit (pin Repetitive short circuit shutdown current limit (see ...
Page 5
Parameter and Conditions ° unless otherwise specified Input and Status Feedback Input resistance T =-40..150°C, see circuit page 6 j Input turn-on threshold voltage Input turn-off threshold voltage ...
Page 6
Truth Table Input- Output level level Normal L L operation H H Open load Short circuit Overtem perature H L Undervoltage Overvoltage ...
Page 7
Status output R ST(ON) GND ESD-Zener diode: 6.1 V typ., max 5 mA; R mA, ESD zener diodes are not to be used as voltage clamp at DC conditions. Operation in this mode may result in a drift of the ...
Page 8
GND disconnect with GND pull PROFET ST 4 GND GND bb Any kind of load device stays off GND > IN IN(T+) ...
Page 9
Typ. transient thermal impedance chip case Z = f(t )Z [K/W] thJC p thJC 10 1 0.1 0.01 1E-5 1E-4 1E-3 1E-2 Transient thermal impedance chip ambient air Z = f(t )Z [K/W] thJA p thJA 100 10 1 0.1 ...
Page 10
Timing diagrams Figure 1a: V turn on OUT ST open drain proper turn on under all conditions Figure 2a: Switching a lamp OUT I L Semiconductor Group Figure 2b: Switching an inductive ...
Page 11
Figure 4a: Overtemperature: Reset if T < OUT T J Figure 5a: Open load: detection in ON-state, turn on/off to open load IN t d(ST OUT I L open The status delay time ...
Page 12
Figure 6a: Undervoltage bb(under) V OUT ST open drain Figure 6b: Undervoltage restart of charge pump bb(over bb(o rst) bb(u rst) V bb(u cp) V bb(under) charge pump starts at V ...
Page 13
Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS426L1 TO-220AB/5, Option E3043 BTS426L1 E3043 Semiconductor Group Ordering code SMD TO-220AB/5, Opt. E3062 Q67060-S6108-A2 BTS426L1 E3062A Changed since 04.96 Date Change Ordering code Dec t 1996 to 800µs, typical ...
Page 14
... Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81669 München © Infineon Technologies AG 2001 All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein ...