LM111E-SMD National Semiconductor, LM111E-SMD Datasheet - Page 4

• Manufacturer Part Number: LM111E-SMD
• Description: LM111/LM211/LM311 Voltage Comparator; Package: LCC; No of Pins: 20; Qty per Container: 50; Container: Rail
• Manufacturer: National Semiconductor

www.national.com
Input Offset Voltage (Note 16)
Input Offset Current(Note 16)
Input Bias Current
Voltage Gain
Response Time (Note 17)
Saturation Voltage
Strobe ON Current (Note 18)
Output Leakage Current
Input Offset Voltage (Note 16)
Input Offset Current (Note 16)
Input Bias Current
Input Voltage Range
Saturation Voltage
Positive Supply Current
Negative Supply Current
5.0 Absolute Maximum Ratings for
the LM311
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Electrical Characteristics
Note 12: “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.”
Note 13: This rating applies for
negative supply voltage or 30V below the positive supply, whichever is less.
Note 14: The maximum junction temperature of the LM311 is 110˚C. For operating at elevated temperature, devices in the H08 package must be derated based
on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line package is 100˚C/W, junction to
ambient.
Note 15: These specifications apply for V
bias current specifications apply for any supply voltage from a single 5V supply up to
Note 16: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and R
Note 17: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 18: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe
pin to ground; it should be current driven at 3 to 5 mA.
Note 19: Human body model, 1.5 kΩ in series with 100 pF.
Total Supply Voltage (V
Output to Negative Supply Voltage
(V
Ground to Negative Supply Voltage
(V
Differential Input Voltage
Input Voltage (Note 13)
Power Dissipation (Note 14)
ESD Rating (Note 19)
74
14
)
)
Parameter
(Note 12)
84
±
)
15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
S
=
±
15V and Pin 1 at ground, and 0˚C
T
T
T
T
T
V
T
T
V
T
V
R
V
V
T
T
A
A
A
A
A
A
A
A
A
A
IN
IN
−
S
+
IN
=25˚C, R
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C, I
≥4.5V, V
=25˚C
=25˚C
≤50K
≤−10 mV, I
≥10 mV, V
= Pin 1 = −5V
≤−10 mV, I
(Note 15)
Conditions
STROBE
−
S
500 mW
=0
≤50k
OUT
OUT
OUT
±
±
300V
for the LM311
36V
40V
30V
30V
15V
=35V
=3 mA
=50 mA
≤8 mA
4
<
T
A
±
Output Short Circuit Duration
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 10 sec)
Voltage at Strobe Pin
Soldering Information
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
<
15V supplies.
Dual-In-Line Package
Small Outline Package
+70˚C, unless otherwise specified. The offset voltage, offset current and
Soldering (10 seconds)
Vapor Phase (60 seconds)
Infrared (15 seconds)
−14.5
Min
40
S
.
13.8,−14.7
0.75
0.23
Typ
100
200
200
2.0
6.0
2.0
0.2
5.1
4.1
Max
13.0
250
300
7.5
1.5
5.0
0.4
7.5
5.0
50
50
10
70
−65˚C to 150˚C
0˚ to 70˚C
10 sec
V
260˚C
260˚C
215˚C
220˚C
Units
V/mV
+
mV
mA
mV
mA
mA
nA
nA
nA
nA
nA
ns
V
V
V
−5V