LM111E-SMD National Semiconductor, LM111E-SMD Datasheet - Page 3

• Manufacturer Part Number: LM111E-SMD
• Description: LM111/LM211/LM311 Voltage Comparator; Package: LCC; No of Pins: 20; Qty per Container: 50; Container: Rail
• Manufacturer: National Semiconductor

Input Offset Voltage (Note 7)
Input Offset Current
Input Bias Current
Voltage Gain
Response Time (Note 8)
Saturation Voltage
Strobe ON Current (Note 9)
Output Leakage Current
Input Offset Voltage (Note 7)
Input Offset Current (Note 7)
Input Bias Current
Input Voltage Range
Saturation Voltage
Output Leakage Current
Positive Supply Current
Negative Supply Current
4.0 Absolute Maximum Ratings for
the LM111/LM211
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Electrical Characteristics
Note 4: This rating applies for
negative supply voltage or 30V below the positive supply, whichever is less.
Note 5: The maximum junction temperature of the LM111 is 150˚C, while that of the LM211 is 110˚C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line
package is 110˚C/W, junction to ambient.
Note 6: These specifications apply for V
temperature specifications are limited to −25˚C≤T
5V supply up to
Note 7: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and R
Note 8: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 9: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin
to ground; it should be current driven at 3 to 5 mA.
Note 10: Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.
Note 11: Human body model, 1.5 kΩ in series with 100 pF.
Total Supply Voltage (V
Output to Negative Supply Voltage
(V
Ground to Negative Supply Voltage
(V
Differential Input Voltage
Input Voltage (Note 4)
Output Short Circuit Duration
Operating Temperature Range
74
14
)
)
Parameter
±
15V supplies.
84
±
)
15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
(Note 10)
S
=
±
15V and Ground pin at ground, and −55˚C≤T
A
T
T
T
T
T
V
T
T
V
T
R
V
Pull-Up May Go To 5V
V
V
V
T
T
≤+85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single
A
A
A
A
A
IN
A
A
IN
A
+
+
IN
IN
A
A
S
=25˚C, R
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C
=25˚C, I
=15V, V
≥4.5V, V
=25˚C
=25˚C
≤50 k
≤−5 mV, I
≥5 mV, V
≤−6 mV, I
≥5 mV, V
(Note 6)
Conditions
STROBE
−
−
S
=−15V, Pin 7
=0
OUT
OUT
≤50k
OUT
OUT
10 sec
for the LM111 and LM211
±
±
=35V
=35V
36V
50V
30V
30V
15V
=50 mA
≤8 mA
=3 mA
3
Lead Temperature (Soldering, 10 sec)
Voltage at Strobe Pin
Soldering Information
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
ESD Rating (Note 11)
LM111
LM211
Dual-In-Line Package
Small Outline Package
Soldering (10 seconds)
Vapor Phase (60 seconds)
Infrared (15 seconds)
A
−14.5
≤+125˚C, unless otherwise stated. With the LM211, however, all
Min
40
S
.
13.8,-14.7
0.75
0.23
Typ
200
200
0.7
4.0
2.0
0.2
0.1
5.1
4.1
60
Max
13.0
100
150
3.0
1.5
5.0
4.0
0.4
0.5
6.0
5.0
10
10
20
−55˚C to 125˚C
−25˚C to 85˚C
www.national.com
V
260˚C
260˚C
215˚C
220˚C
Units
V/mV
300V
+
mV
mA
mV
mA
mA
nA
nA
nA
nA
nA
µA
ns
−5V
V
V
V