MKP1848 Vishay Siliconix, MKP1848 Datasheet - Page 12

• Manufacturer Part Number: MKP1848
• Description: Metallized Polypropylene Film Capacitors DC Capacitor MKP Type
• Manufacturer: Vishay Siliconix

MKP 1848 DC-Link
Vishay Roederstein
INSPECTION REQUIREMENTS
General Notes:
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 61071.
www.vishay.com
292
SUB-CLAUSE NUMBER AND TEST
ROUTINE TEST-FINAL INSPECTION
5.14.2.1 External inspection,
5.14.2.2 Dimensions
5.3.1
5.3.2
5.5.1.2
5.7
TYPE TESTS
5.14.2
5.14.0
5.14.1.1.4 Robustness of terminations
5.14.1.6 Resistance to soldering heat
5.14.4
5.14.0
5.14.3.1 Vibration
5.14.3.2 Shock or impact
5.14.4
Capacitance
tan δ
Voltage test between terminal
Insulation resistance
External inspection
Initial measurements
IEC 60068-2-21
IEC 60068-2-20
Final measurements
IEC 60068-2-6
IEC 60068-2-6
Final measurements
visual examination
Initial measurements
Metallized Polypropylene Film Capacitors
For technical questions, contact: [e-mail]
CONDITIONS
1 kHz at room temperature
1 kHz at room temperature
10 kHz at room temperature
1.5 x U
Duration 10 s
U
at room temperature
U
at room temperature
Duration 1 min
Check for finish, marking and overall
dimensions
Capacitance at 1 kHz
tan δ at 10 kHz
Tensile Ua1
Wire diameter
≤ 0.8 mm
≤ 1.25 mm
Duration 10 s ± 1 s
Bending Ub method 1
Wire diameter
≤ 0.8 mm
≤ 1.25 mm
4 x 90 °,
Duration 2 s to 3 s/bend
No predrying, Method 1A
Solder bath: 260 °C ± 5 °C
Capacitance
tan δ
Capacitance at 1 kHz
tan δ at 10 kHz
10 Hz to 55 Hz: amplitude ± 0.35 mm or
acceleration 98 m/s
Test duration: 10 frequency cycles, 3 axes
offset from each other by 90°
1 octave/min
Pulse shape: half sine
Acceleration: 490 m/s
Duration t of pulse: 11 ms
Visual examination
Capacitance
tan δ
Ndc
Ndc
DC Capacitor MKP Type
≤ 500 V measuring voltage 100 V
> 500 V m,easuring voltage 500 V
Ndc
at T
amb
.
section
≤ 0.5 mm
≤ 1.2 mm
section
≤ 0.05 mm
≤ 0.019 mm
2
2
2
2
3
load
10 N
20 N
3
10 N
load
20 N
PERFORMANCE REQUIREMENTS
Legible marking as specified
See specification drawing
See specific reference data
See specific reference data
No visible damage or puncture
No flashover
See specific reference data
Legible marking and finish as specified
Dimensions: see specific drawing
|ΔC/C| ≤ 0.5 %
Increase of tan δ ≤ 0.0050
Compared to values measured in 5.14.0
No visible damage
No visible damage
|ΔC/C| ≤ 0.5 %
Increase of tan δ ≤ 0.0050
Compared to values measured in 5.14.0
Document Number: 28164
www.DataSheet4U.com
Revision: 02-Feb-09