TLE6254-2G Infineon Technologies AG, TLE6254-2G Datasheet
TLE6254-2G
Related parts for TLE6254-2G
TLE6254-2G Summary of contents
Page 1
Fault Tolerant Differential CAN-Transceiver Final Data Sheet 1 Features • Data transmission rate up to 125 kBaud • Very low current consumption in stand-by and sleep operation mode • Implemented receive-only mode • Optimized EMC behavior • Wake-up input pin, ...
Page 2
Pin Configuration (top view) Figure 1 Table 1 Pin Definitions and Functions Pin No. Symbol 1 INH 2 TxD 3 RxD 4 NERR 5 NSTB 6 ENT Data Sheet Version 1.4 P-DSO-14-13 INH 1 2 TxD RxD 3 NERR ...
Page 3
Table 1 Pin Definitions and Functions (cont’d) Pin No. Symbol RTH 9 RTL CANH 12 CANL 13 GND Data Sheet Version 1.4 Function Wake-Up input; if level of indicates a ...
Page 4
Functional Block Diagram RTL 9 CANH 11 CANL 12 RTH 8 Filter GND 13 Figure 2 Block Diagram Data Sheet Version 1.4 Vcc (normal, stand-by, sleep) Driver Output Stage Temp.- Protection 7.2 1.8 -2.8 3.2 7.2 ...
Page 5
Circuit Description The CAN transceiver TLE 6254-2G works as the interface between the CAN protocol controller and the physical CAN bus-lines. Figure 3 shows the principle configuration of a CAN network. The TLE 6254-2G is optimized for low-speed data ...
Page 6
Power Down Normal Mode NSTB 1 ENT 0 RxD-Only NSTB 1 NSTB 0 NSTB ENT Go to Sleep Mode NSTB ENT 0 Figure 4 State Diagram Data Sheet Version 1.4 Start Up Power Up ENT INH NSTB 1 high ENT ...
Page 7
Operation Modes, Wake-Up In addition to the normal operation mode, the TLE 6254-2G offers a receive-only mode as well as two low power operation modes to save power during periods that do not require communication on the CAN bus: ...
Page 8
If either of the supply voltages drops below the specified limits, the transceiver is automatically switched to . Table 2 Truth Table of the CAN Transceiver NSTB ENT Mode stand-by BAT 1) mode 0 0 sleep mode ...
Page 9
When one of the bus failures and 7 is detected, the defective bus wire is disabled by switching off the affected bus termination and the respective output stage. A wake-up from sleep mode via the bus ...
Page 10
Application Hints Table 4 Not Needed Pins Pin Symbol Recommendation INH Leave open NERR Leave open NSTB Connect to ENT Connect to WAKE Connect to consumption by approx. 5 µA The transceiver will stay in a present operating mode ...
Page 11
Absolute Maximum Ratings Parameter V Input voltage at BAT V Logic supply voltage CC Input voltage at TxD, RxD, NERR, NSTB and ENT Input voltage at CANH and CANL Transient voltage at CANH and CANL Input voltage at WAKE ...
Page 12
Operating Range Parameter Logic input voltage Battery input voltage Termination resistances at RTL and RTH Junction temperature Thermal Resistance Junction ambient Thermal Shutdown Junction temperature Wake Input Voltage Wake input voltage Note: In the operating range, the functions given ...
Page 13
Static Characteristics 4. 5. (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter V V Supplies , CC S Supply current Supply current (Receive-only ...
Page 14
Static Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Transmission Input T D, Not Stand-By NSTB and Enable Transfer ...
Page 15
Static Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Bus Lines CANL, CANH Differential receiver recessive-to-dominant threshold voltage Differential ...
Page 16
Static Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Voltage detection threshold for short-circuit to battery voltage on CANH ...
Page 17
Static Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Termination Outputs RTL, RTH V RTL to switch-on CC resistance ...
Page 18
Dynamic Characteristics 4. 5. (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter CANH and CANL bus output transition time recessive-to-dominant CANH and CANL ...
Page 19
Dynamic Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Propagation delay TxD-to-RxD LOW (recessive to dominant) Propagation delay TxD-to-RxD ...
Page 20
Dynamic Characteristics (cont’ (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Propagation delay TxD-to-RxD HIGH (dominant to recessive) Minimum hold time ...
Page 21
Test and Application + 5 V WAKE Figure 5 Test Circuits For isolated testing the CAN Bus Substitute 1 is connected to the CAN Transceiver (see Figure 5). The capacitors termination resistors R RTH lines is simulated by switching ...
Page 22
V bat CAN bus 100 nF 22 µF *) optional, according to car manufacturers requirements Figure 6 Application Circuit Data Sheet Version 1.4 choke TLE 6254-2G *) CANH RxD 11 3 CANL TxD RTH RTH 8 ENT ...
Page 23
Package Outlines P-DSO-14-13 (Plastic Dual Small Outline Package) Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information” SMD = Surface Mounted Device Data Sheet Version 1.4 Final Data TLE 6254-2G 23 ...
Page 24
... Edition 2003-07-22 Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81541 München, Germany © Infineon Technologies AG 2003. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be consid- ered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, ...