TLE6217 Infineon Technologies, TLE6217 Datasheet
TLE6217
Available stocks
Related parts for TLE6217
TLE6217 Summary of contents
Page 1
Smart Quad Channel Low-Side Switch Features Shorted Circuit Protection Overtemperature Protection Overvoltage Protection Parallel Control of the Inputs (PWM Applications) Separate Diagnostic Pin for Each Channel Power - Package with integrated cooling area Standby mode with low ...
Page 2
Page 30. 07. 2002 ...
Page 3
Pin Configuration (Top view) www.DataSheet4U.com P - DSO - Pin Description Pin Symbol 1 GND 2 OUT1 3 ST1 4 IN4 STBY 7 IN3 8 ST2 9 OUT2 10 GND 11 GND 12 OUT3 ...
Page 4
STBY ENA IN1 ST1 www.DataSheet4U.com IN4 ST4 IN2 ST2 IN3 ST3 Detailed ...
Page 5
Maximum Ratings for T The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the IC will result. Parameter Supply voltage Continuous drain source voltage (OUT1...OUT4) Input voltage IN1 to IN4, ...
Page 6
Electrical Characteristics Parameter and Conditions ° 150 ° (unless otherwise specified) 1. Power Supply (V S Supply current (Outputs ON) Supply current (Outputs OFF) V ...
Page 7
Electrical Characteristics Parameter and Conditions – 40 ° 150 ° (unless otherwise specified) 5. Standby Input (STBY) Input low voltage Input high voltage Input current 6. Diagnostic ...
Page 8
This IC is especially designed to drive inductive loads (relays, electromagnetic valves). Integrated clamp-diodes limit the output voltage when inductive loads are discharged. Four open-drain logic outputs indicate the status of the integrated circuit. The following conditions are monitored and ...
Page 9
Open load is detected for all four channels in on and off mode. In the on mode the load current is monitored drops below the specified threshold value IQU then an open load condition is detected. In the ...
Page 10
Note 2): to reset latched status-output in case of overload/short-to-supply/overtemperature the control input has to go low and stay low for longer than max. Input suppression time t characteristics Logic Block Diagram Overtemperature 1.....overtemperature 0.....normal cond. ENA 1....enabled 0... disabled ...
Page 11
Output Slope INL 85% www.DataSheet4U.com Overload Switch OFF Delay D(lim) I D(OL ...
Page 12
Test Circuit www.DataSheet4U.com TLE 6217 GP Page 30. 07. ...
Page 13
Application Circuit www.DataSheet4U.com The blocking capacitor C is recommended to avoid critical negative voltage spikes case of battery interruption during OFF-commutation ...
Page 14
Timing Diagrams of Diagnostic with Pulsed Input Signal Normal condition, resistive load, pulsed input signal www.DataSheet4U.com V ST Current Overload DSO Input suppression time ...
Page 15
Diagnostic status output at different open load current conditions www.DataSheet4U.com leads to a static status signal INOFF ...
Page 16
Normal operation, followed by open load condition 12V www.DataSheet4U.com D(OL ...
Page 17
... Ordering code Type TLE6217 G TLE6217 C Pad Assignment www.DataSheet4U.com Out Out Ordering Code on request on request VR1 center STB IN Page Package P - DSO - 20 – ...
Page 18
Package dimensions All dimensions in mm www.DataSheet4U.com 15.74 +/- 0. 1 13.7 ...
Page 19
Revision List: 01.09.2001 Target Datasheet 01.10.2001 First revision 01.12.2001 Second revision 30.04.2002 Third revision 30.07.2002 Preliminary Datasheet www.DataSheet4U.com ...
Page 20
... Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life- support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...