S2006FS221V Teccor Electronics, Inc., S2006FS221V Datasheet - Page 160

• Manufacturer Part Number: S2006FS221V
• Description: Thyristor Product Catalog
• Manufacturer: Teccor Electronics, Inc.

AN1006
Procedure 2: (+)V
To measure the (+)V
1. Set Left-Right Terminal Jack Selector to correspond with
2. Increase Variable Collector Supply Voltage to the rated
Procedure 3: (-)V
To measure the (-)V
1. Set Polarity to (–).
2. Repeat Procedures 1 and 2. (Read measurements from
Procedure 4: V
To measure the V
1. Set Terminal Selector to Step Generator-Emitter Grounded.
2. Set Step/Offset Amplitude to twice the maximum I
3. Set Variable Collector Supply Voltage Range to 15 V Max
4. Set Offset by depressing 0 (zero).
5. Set Rate by depressing Norm.
6. Set Step Family by depressing Rep (Repetitive).
7. Set Mode to Norm.
8. Set Horizontal knob to 0.5 V/DIV.
9. Set Power Dissipation to 220 W (100 W on 577).
10. Set Number of Steps to 1.
11. Set Step/Offset Polarity to non-inverted (button extended;
12. Set Vertical knob to a sufficient setting to allow the viewing
Note the following:
•
http://www.teccor.com
[phone]
location of the test fixture.
V
across horizontally from the dot to the vertical current scale.
This measured value is the leakage current.
(Figure AN1006.11)
upper right corner of the screen.)
of the device (to insure the device turns on).
Peak volts. (16 V on 370)
on 577 button depressed).
of 1.4 times the I
Due to the excessive amount of power that can be generated in
this test, only parts with an I
tested on standard curve tracer. If testing devices above 8 A, a
Tektronix model 176 high-current module is required.
Figure AN1006.11 (+)I
DRM
of the device and observe the dot on the CRT. Read
V DRM
TM (Forward and Reverse)
TM (Forward and Reverse)
DRM
DRM
DRM
DRM
T(RMS)
, (-)I
, (+)I
and (-)I
and (+)I
DRM
rating of the device [I
DRM
DRM
= 205 nA at (+)V
T(RMS)
DRM
I DRM
DRM
parameter:
parameter:
rating of 8 A or less should be
parameter:
DRM
= 600 V
T(peak)
PER
DIV
PER
DIV
PER
PER
V
E
R
H
O
R
S
E
P
DIV
9m
DIV
T
Z
T
()k
I
on CRT].
100
nA
50
V
GT
rating
AN1006 - 8
•
Procedure 5: V
To measure the V
1. Set Polarity to (+).
2. Set Left-Right Terminal Jack Selector to correspond with
3. Increase Variable Collector Supply Voltage until current
Note: Model 370 current is limited to 10 A.
WARNING: Limit test time to 15 seconds maximum. After
the Variable Collector Supply Voltage has been set to I
the test time can automatically be set to a short test time by
changing Step Family from repetitive to single by depress-
ing the Single button.
To measure V
the trace crosses the I
hand side of scale to the crossing point is the V
(Figure AN1006.12)
Procedure 6: V
To measure the V
1. Set Polarity to (–).
2. Set Left-Right Terminal Jack Selector to correspond with
3. Increase Variable Collector Supply Voltage until current
4. Measure V
Procedure 7: I
To measure the I
1. Set Step/Offset Amplitude to twice the I
2. Set Power Dissipation to 10 W.
A Kelvin test fixture is required for this test. If a Kelvin fixture is
not used, an error in measurement of V
age drop in fixture. If a Kelvin fixture is not available,
Figure AN1006.3 shows necessary information to wire a test
fixture with Kelvin connections.
location of test fixture.
reaches rated I
triac under test.
the location of the test fixture.
reaches rated I
upper right hand corner of screen.
device.
Figure AN1006.12 V
V TM
TM
TM(Reverse)
, follow along horizontal scale to the point where
H(Forward and Reverse)
TM (Forward)
TM (Reverse)
H (Forward and Reverse)
TM (Forward)
TM (Reverse)
T(peak)
T(peak)
I PK
T(peak)
TM (forward)
similar to Figure AN1006.12, except from
, which is 1.4 times I
.
parameter:
parameter:
value. The distance from the left-
= 1.1 V at I
parameter:
©2002 Teccor Electronics
PK
Thyristor Product Catalog
TM
= 11.3 A (8 A rms)
will result due to volt-
T(RMS)
GT
TM
rating of the
Application Notes
value.
PER
PER
PER
PER
rating of the
DIV
DIV
DIV
DIV
()k
9m
V
E
R
T
H
O
R
Z
S
T
E
P
I
2
500
100
mV
mA
20
A
T(peak)
,