T315XW01V9 AUO, T315XW01V9 Datasheet
T315XW01V9
Related parts for T315XW01V9
T315XW01V9 Summary of contents
Page 1
AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed Product Specifications 31.5” WXGA Color TFT-LCD Module Model Name: T315XW01 Preliminary Specifications (*) Final Specifications ...
Page 2
No COVER CONTENTS RECORD OF REVISIONS 1 GENERAL DESCRIPTION 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL SPECIFICATIONS 3-1 ELECTRICAL CHARACTREISTICS 3-2 INTERFACE CONNECTIONS 3-3 SIGNAL TIMING SPECIFICATIONS 3-4 SIGNAL TIMING WAVEFORMS 3-5 COLOR INPUT DATA REFERNECE 3-6 POWER SEQUENCE 4 OPTICAL ...
Page 3
Version Date No 0.1 2005/8/2 All 1.0 2005/10/12 6 Electrical Characteristics: TBD 9 Inverter specs : TBD 18,19 20 Shock : 50G/11ms 1.1 2005/10/17 16 Response time : max 20ms 1.2 2005/11/ min : 800ms 1.3 2005/12/2 14 ...
Page 4
General Description This specification applies to the 31.51 inch Color TFT-LCD Module T315XW01 V9. This LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 31.51 inch. This module supports 1366x768 XGA-WIDE ...
Page 5
Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause permanent damage to the unit. Item LCD Drive Voltage Input Voltage of Signal BLU Input Voltage BLU Brightness Control Voltage Operating Temperature Operating Humidity Storage Temperature ...
Page 6
Electrical Specification The T315XW01 V9 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the BLU power inverter.. 3-1 Electrical ...
Page 7
When you confirm it, the LCD Assembly should be operated in the same condition as installed in your instrument not attach a conducting tape to lamp connecting wire. ...
Page 8
... No Reproduction and Redistribution Allowed Description T315XW01 V9 - Specs. Ver 1.5 Default NS mode AUO internal test AUO internal test AUO internal test 8/ ...
Page 9
LVDS Option = High Previous Cycle Clock RIN0 RIN0- RIN1 RIN1- RIN2 RIN2- RIN3 RIN3- LVDS Option = Low or Open Previous Cycle Clock RIN0 ...
Page 10
BACKLIGHT CONNECTOR PIN CONFIGURATION 1.Electrical specification Item Input Voltage Input Current Input Power Inrush Current Output Frequency On/Off Control Voltage VBLON I_VBLON On/Off Control Current Dimming Control Voltage VDIM Dimming Control Current I_VDIM External PWM Control Voltage PDIM External PWM ...
Page 11
Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation. Signal Item Symbol Min Period Tv ...
Page 12
Signal Timing Waveforms ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed www.DataSheet.co.kr T315XW01 V9 - Specs. Ver 1.5 12/25 Datasheet pdf - http://www.DataSheet4U.net/ ...
Page 13
Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below ...
Page 14
Power Sequence 90% Power Supply For LCD 10 (+12V) GND Interface Signal (LVDS data & CLK) GND Backlight on/off control signal (VBLON) Parameter Min. t1 470 t2 t3 700 or (200)*1 t4 200 t5 t6 0.47 t7 ...
Page 15
Power Sequence for Inverter Power input for Backlight VDDB Enable Back light on/off (VBLON) Dimming control signal VDIM VDDB V (Typ)×0.8 DDB 0V Parameter Min 500 ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. ...
Page 16
Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark environment at 25℃. The values specified are at an approximate distance 50cm from the LCD surface at a ...
Page 17
Note: 1. Contrast Ratio (CR) is defined mathematically as: Contrast Ratio= 2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2. When ...
Page 18
FIG.3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “any level of gray(bright) “ and “any level of gray(dark)”. Any level of gray(Bright) Any level of gray(Dark) ...
Page 19
Mechanical Characteristics The contents provide general mechanical characteristics for the model T315XW01 V9. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Bezel Opening Active Display Area Weight Surface Treatment ©Copyright ...
Page 20
Front View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V9 - Specs. Ver ...
Page 21
Rear View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V9 - Specs. Ver ...
Page 22
Reliability Environment test condition No 1 High temperature storage test 2 Low temperature storage test 3 High temperature operation test 4 Low temperature operation test 5 Vibration test (non-operating) 6 Shock test (non-operating) 7 Vibration test (with carton) 8 ...
Page 23
International Standard 7-1. Safety (1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995 Standard for Safety of Information Technology Equipment Including electrical Business Equipment. (2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association, Standard for Safety of ...
Page 24
Packing Label : 83mm * 23mm Carton Label : 80mm * 40mm AU O ptronics MODEL NO: T315XW01 VX PART NO: 9731T01.XXX CUSTOMER NO: CARTON NO: *PM100-01A1600001* Made in Taiwan ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. ...
Page 25
Carton : 3pcs Modules 947(L)mm * 290(W)mm * 595(H)mm ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed ...
Page 26
PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1 MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure ...
Page 27
ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-4 PRECAUTIONS ...