T315XW01V5 AUO, T315XW01V5 Datasheet
T315XW01V5
Available stocks
Related parts for T315XW01V5
T315XW01V5 Summary of contents
Page 1
... Product Description: AUO Model Name: T315XW01 V5 Customer Part No/Project Name Customer Signature ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed : Date AUO T315XW01 V5 - Specs. Ver 1.4 Date 1/ ...
Page 2
AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed Product Specifications 31.5” WXGA Color TFT-LCD Module Model Name: T315XW01 Preliminary Specifications ...
Page 3
No COVER CONTENTS RECORD OF REVISIONS 1 GENERAL DESCRIPTION 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL SPECIFICATIONS 3-1 ELECTRICAL CHARACTREISTICS 3-2 INTERFACE CONNECTIONS 3-3 SIGNAL TIMING SPECIFICATIONS 3-4 SIGNAL TIMING WAVEFORMS 3-5 COLOR INPUT DATA REFERNECE 3-6 POWER SEQUENCE 4 OPTICAL ...
Page 4
Version Date No 0.1 2005/5/20 All 0.2 2005/6/13 9 VDIM : 1.0 2005/8/1 Preliminary specs 1.1 2005/10/4 7 LVDS pin11 definition : Reserved LVDS pin11 definition : 9 Inverter pin11 Note : 1.2 2005/10/ ...
Page 5
General Description This specification applies to the 31.51 inch Color TFT-LCD Module T315XW01 V5. This LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 31.51 inch. This module supports 1366x768 XGA-WIDE ...
Page 6
Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause permanent damage to the unit. Item Logic/LCD Drive Voltage Input Voltage of Signal BLU Input Voltage BLU Brightness Control Voltage Operating Temperature Operating Humidity Storage Temperature ...
Page 7
Electrical Specification The T315XW01 V5 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the BLU power inverter.. 3-1 Electrical ...
Page 8
When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, ...
Page 9
... All Vcc (power input) pins should be connected together. ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed Description www.DataSheet.co.kr Low:0~0.7V, High:2.4V~5.5V T315XW01 V5 - Specs. Ver 1.4 note Auo internal test pin Auo internal test pin Auo internal test pin Auo internal test pin 9/29 Datasheet pdf - http://www.DataSheet4U.net/ ...
Page 10
LVDS Option = L (GND) Previous Cycle Clock RIN0 RIN0- RIN1 RIN1- RIN2 RIN2- RIN3 RIN3- LVDS Option = H (3.3V) or Open Previous Cycle Clock RIN0+ R1 ...
Page 11
Correspondence between input data and display image Rotate function = Low or Open 1,1 1,2 1,3 2,1 2,2 2,3 3,1 3,2 3,3 768,1 768,2 768,3 Rotate function = High 768,1366 768,1365 768,1364 767,1366 767,1365 767,1364 766,1366 766,1365 766,1364 1,1366 1,1365 ...
Page 12
BACKLIGHT CONNECTOR PIN CONFIGURATION １． Electrical specification Item Symb. VDDB Input Voltage IDDB Input Current Input Power PDDB IRUSH Inrush Current Output Frequency FBL On/Off Control Voltage VB LON On/Off Control Current IBLON Dimming Control Voltage VDIM Dimming Control Current ...
Page 13
Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation. * Timing Table DE only Mode ...
Page 14
Signal Timing Waveforms ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed www.DataSheet.co.kr T315XW01 V5 - Specs. Ver 1.4 14/29 Datasheet pdf - http://www.DataSheet4U.net/ ...
Page 15
Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below ...
Page 16
Power Sequence 90% Power Supply For LCD 10% V (+5V) cc GND Interface Signal (LVDS data & CLK) GND Backlight on/off control signal (VBLON) Parameter Min 700 (1) Apply the ...
Page 17
Power Sequence for Inverter 90% 24V(typ.) Power input for Backlight 10% VDDB T1 T2 Enable Back light on/off (VBLON) Dimming control signal VDIM Deep condition for Inverter VDDB V (Typ)×０．８ DDB ０V Parameter Min 500 T3 250 ...
Page 18
Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark environment at 25℃. The values specified are at an approximate distance 50cm from the LCD surface at a ...
Page 19
Note: 1. Contrast Ratio (CR) is defined mathematically as: Contrast Ratio= 2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2. When ...
Page 20
FIG.3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “any level of gray(bright) “ and “any level of gray(dark)”. Any level of gray(Bright) Any level of gray(Dark) ...
Page 21
Mechanical Characteristics The contents provide general mechanical characteristics for the model T315XW01 V5. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Bezel Opening Active Display Area Weight Surface Treatment ©Copyright ...
Page 22
Front View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V5 - Specs. Ver ...
Page 23
Rear View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V5 - Specs. Ver ...
Page 24
Reliability Environment test condition No 1 High temperature storage test 2 Low temperature storage test 3 High temperature operation test 4 Low temperature operation test 5 Vibration test (non-operating) 6 Shock test (non-operating) 7 Vibration test (with carton) 8 ...
Page 25
International Standard 7-1. Safety (1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995 Standard for Safety of Information Technology Equipment Including electrical Business Equipment. (2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association, Standard for Safety of ...
Page 26
Packing Label : 83mm * 23mm Carton Label : 80mm * 40mm AU O ptronics MODEL NO: T315XW01 VX PART NO: 9731T01.XXX CUSTOMER NO: CARTON NO: *PM100-01A1600001* Made in Taiwan ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. ...
Page 27
Carton : 3pcs Modules 947(L)mm * 290(W)mm * 595(H)mm ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed ...
Page 28
PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1 MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure ...
Page 29
ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-4 PRECAUTIONS ...