ISL6545A Intersil Corporation, ISL6545A Datasheet - Page 7

• Manufacturer Part Number: ISL6545A
• Description: Single Synchronous Buck Pulas Width MoDulation
• Manufacturer: Intersil Corporation

resistive load connected to the output will help pull down the
voltage (at the RC rate of the R of the load and the C of the
output capacitance).
If the V
supply that comes up after V
through its cycle, but with no output voltage ramp. When V
turns on, the output would follow the ramp of the V
close to 100% duty cycle, with COMP/SD pin >4V), from
zero up to the final expected voltage. If V
may be excessive inrush current charging the output
capacitors (only the beginning of the ramp, from zero to
V
changing the sequencing of the power supplies, or sharing
the same supply, or adding sequencing logic to the
COMP/SD pin to delay the soft-start until the V
ready (see Input Voltage Considerations).
If the IC is disabled after soft-start (by pulling COMP/SD pin
low), and then enabled (by releasing the COMP/SD pin),
then the full initialization (including OCP sample) will take
place. However, that there is no new OCP sampling during
overcurrent retries.
If the output is shorted to GND during soft-start, the OCP will
handle it, as described in the next section.
Overcurrent Protection (OCP)
The overcurrent function protects the converter from a shorted
output by using the lower MOSFET’s on-resistance, r
to monitor the current. A resistor (R
overcurrent trip level (see Typical Application diagram). This
method enhances the converter’s efficiency and reduces cost
by eliminating a current sensing resistor. If overcurrent is
detected, the output immediately shuts off, it cycles the soft-
start function in a hiccup mode (2 dummy soft-start time-outs,
then up to one real one) to provide fault protection. If the
shorted condition is not removed, this cycle will continue
indefinitely.
GND>
GND>
GND>
OUT
matters here). If this is not acceptable, then consider
IN
V
V
V
to the upper MOSFET drain is from a different
OUT
OUT
OUT
FIGURE 3. SOFT-START WITH PRE-BIAS
OVER-CHARGED
PRE-BIASED
NORMAL
T0
T1
CC
7
, the soft-start would go
OCSET
IN
) programs the
is too fast, there
IN
T2
supply is
IN
ISL6545, ISL6545A
DS(ON)
(at
IN
,
Following POR (and 6.8ms delay), the ISL6545 initiates the
Overcurrent Protection sample and hold operation. The
LGATE driver is disabled to allow an internal 21.5μA current
source to develop a voltage across R
samples this voltage (which is referenced to the GND pin) at
the LGATE/OCSET pin, and holds it in a counter and DAC
combination. This sampled voltage is held internally as the
Overcurrent Set Point, for as long as power is applied, or
until a new sample is taken after coming out of a shut-down.
The actual monitoring of the lower MOSFET’s on-resistance
starts 200ns (nominal) after the edge of the internal PWM
logic signal (that creates the rising external LGATE signal).
This is done to allow the gate transition noise and ringing on
the PHASE pin to settle out before monitoring. The monitoring
ends when the internal PWM edge (and thus LGATE) goes
low. The OCP can be detected anywhere within the above
window.
If the regulator is running at high UGATE duty cycles (around
75% for 600kHz or 87% for 300kHz operation), then the
LGATE pulse width may not be wide enough for the OCP to
properly sample the r
is too narrow (or not there at all) for 3 consecutive pulses,
then the third pulse will be stretched and/or inserted to the
425ns minimum width. This allows for OCP monitoring every
third pulse under this condition. This can introduce a small
pulse-width error on the output voltage, which will be
corrected on the next pulse; and the output ripple voltage will
have an unusual 3-clock pattern, which may look like jitter.
This is not necessarily a problem; it is more of a compromise
to maintain OCP at the higher duty cycles. If the OCP is
disabled (by choosing a too-high value of R
resistor at all), then the pulse stretching feature is also
disabled. Figure 4 illustrates the LGATE pulse width
stretching, as the width gets smaller.
FIGURE 4. LGATE PULSE STRETCHING
DS(ON)
> 425 ns
= 425 ns
< 425 ns
<< 425 ns
. For those cases, if the LGATE
OCSET
. The ISL6545
OCSET
November 15, 2006
, or no
FN6305.3