ISL6545A Intersil Corporation, ISL6545A Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL6545A
Manufacturer Part Number
ISL6545A
Description
Single Synchronous Buck Pulas Width MoDulation
Manufacturer
Intersil Corporation
Datasheet
1.ISL6545A.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6545AIBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6545AIBZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6545AIRZ
Manufacturer:
SEMTECH
Quantity:
60 000
Part Number:
ISL6545AIRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6545AIRZ-T
Manufacturer:
INTERSIL
Quantity:
1 635
Part Number:
ISL6545AIRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
where: I
response time to the application of load, and t
response time to the removal of load. The worst case
response time can be either at the application or removal of
load. Be sure to check both of these equations at the
minimum and maximum output levels for the worst case
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q
small ceramic capacitors physically close to the MOSFETs
and between the drain of Q
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
For a through hole design, several electrolytic capacitors may
be needed. For surface mount designs, solid tantalum
capacitors can also be used, but caution must be exercised
with regard to the capacitor surge current rating. These
capacitors must be capable of handling the surge current at
power-up. Some capacitor series available from reputable
manufacturers are surge current tested.
MOSFET Selection/Considerations
The ISL6545 requires 2 N-Channel power MOSFETs. These
should be selected based upon r
requirements, and thermal management requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss components;
conduction loss and switching loss. The conduction losses are
the largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed between
the two MOSFETs according to duty factor. The switching
t
RISE
=
TRAN
V
L x I
IN
- V
is the transient load current step, t
TRAN
OUT
1
and the source of Q
13
t
FALL
DS(ON)
=
L x I
, gate supply
V
1
OUT
TRAN
turns on. Place the
FALL
2
RISE
.
is the
ISL6545, ISL6545A
is the
losses seen when sourcing current will be different from the
switching losses seen when sinking current. When sourcing
current, the upper MOSFET realizes most of the switching
losses. The lower switch realizes most of the switching
losses when the converter is sinking current (see the
equations below). These equations assume linear voltage-
current transitions and do not adequately model power loss
due the reverse-recovery of the upper and lower MOSFET’s
body diode. The gate-charge losses are dissipated by the
ISL6545 and don't heat the MOSFETs. However, large gate-
charge increases the switching interval, t
the MOSFET switching losses. Ensure that both MOSFETs
are within their maximum junction temperature at high ambient
temperature by calculating the temperature rise according to
package thermal-resistance specifications. A separate heatsink
may be necessary depending upon MOSFET power, package
type, ambient temperature and air flow.
When operating with a 12V power supply for V
to a minimum supply voltage of 6.5V), a wide variety of N-
MOSFETs can be used. Check the absolute maximum V
rating for both MOSFETs; it needs to be above the highest
V
20V V
maximum rating). Low threshold transistors (around 1V or
below) are not recommended, for the reasons explained in
the next paragraph.
For 5V only operation, given the reduced available gate bias
voltage (5V), logic-level transistors should be used for both
N-MOSFETs. Look for r
should be exercised with devices exhibiting very low
V
present aboard the ISL6545 may be circumvented by these
MOSFETs if they have large parasitic impedences and/or
capacitances that would inhibit the gate of the MOSFET from
being discharged below its threshold level before the
complementary MOSFET is turned on. Also avoid MOSFETs
with excessive switching times; the circuitry is expecting
transitions to occur in under 50ns or so.
Losses while Sinking Current
Losses while Sourcing Current
CC
GS(ON)
P
P
P
P
UPPER
LOWER
LOWER
UPPER
voltage allowed in the system; that usually means a
Where: D is the duty cycle = V
GS
characteristics. The shoot-through protection
rating (which typically correlates with a 30V V
= Io
= Io
=
=
t
F
SW
Io
SW
Io
2
2
2
2
x r
x r
is the combined switch ON and OFF time, and
×
is the switching frequency.
×
DS(ON)
DS(ON)
r
r
DS ON
DS ON
(
(
DS(ON)
x D
x (1 - D)
)
)
×
×
D
(
1 D
+
ratings at 4.5V. Caution
–
1
-- - Io
2
OUT
⋅
)
+
/ V
×
1
-- - Io
2
SW
V
⋅
IN
IN
,
×
which increases
×
V
t
SW
IN
CC
November 15, 2006
×
×
t
F
(or down
SW
S
FN6305.3
×
DS
F
S
GS