BD9120HFN Rohm, BD9120HFN Datasheet - Page 41
![no-image](/images/manufacturer_photos/0/5/571/rohm_sml.jpg)
BD9120HFN
Manufacturer Part Number
BD9120HFN
Description
(BD9106FVM - BD9120HFN) Synchronous Buck Converter Integrated FET
Manufacturer
Rohm
Datasheet
1.BD9120HFN.pdf
(42 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BD9120HFN-TR
Manufacturer:
RICOH
Quantity:
3 000
Part Number:
BD9120HFN-TR
Manufacturer:
ROHM/罗姆
Quantity:
20 000
●Precaution for circuit design
●Precaution for Mounting / Circuit board design
●Precautions Regarding Application Examples and External Circuits
Notice - Rev.001
1)
2)
3)
4)
5)
6)
7)
8)
1)
2)
Regarding Precaution for Mounting / Circuit board design, please specially refer to ROHM Mounting specification
1)
2)
The products are designed and produced for application in ordinary electronic equipment (AV equipment, OA
equipment, telecommunication equipment, home appliances, amusement equipment, etc.). If the products are to be
used in devices requiring extremely high reliability (medical equipment, transport equipment, aircraft/spacecraft,
nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose
malfunction or operational error may endanger human life and sufficient fail-safe measures, please consult with the
ROHM sales staff in advance. If product malfunctions may result in serious damage, including that to human life,
sufficient fail-safe measures must be taken, including the following:
The products are designed for use in a standard environment and not in any special environments. Application of the
products in a special environment can deteriorate product performance. Accordingly, verification and confirmation of
product performance, prior to use, is recommended if used under the following conditions:
The products are not radiation resistant.
Verification and confirmation of performance characteristics of products, after on-board mounting, is advised.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta).
When used in sealed area, confirm the actual ambient temperature.
Confirm that operation temperature is within the specified range described in product specification.
Failure induced under deviant condition from what defined in the product specification cannot be guaranteed.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the remainder of flux may negatively affect
product performance and reliability.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
Company in advance.
If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the characteristics
of the products and external components, including transient characteristics, as well as static characteristics.
The application examples, their constants, and other types of information contained herein are applicable only when
the products are used in accordance with standard methods. Therefore, if mass production is intended, sufficient
consideration to external conditions must be made.
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits in the case of single-circuit failure
[a] Use in various types of liquid, including water, oils, chemicals, and organic solvents
[b] Use outdoors where the products are exposed to direct sunlight, or in dusty places
[c] Use in places where the products are exposed to sea winds or corrosive gases, including Cl
[d] Use in places where the products are exposed to static electricity or electromagnetic waves
[e] Use in proximity to heat-producing components, plastic cords, or other flammable items
[f]
[g] Use involving unclean solder or use of water or water-soluble cleaning agents for cleaning after soldering
[h] Use of the products in places subject to dew condensation
and NO
Use involving sealing or coating the products with resin or other coating materials
2
Notice
www.DataSheet.co.kr
2
, H
Datasheet
Datasheet
2
S, NH
3
, SO
2
,
Datasheet pdf - http://www.DataSheet4U.net/