PIC16C745/P Microchip Technology, PIC16C745/P Datasheet - Page 99

• Manufacturer Part Number: PIC16C745/P
• Description: 8-Bit CMOS Microcontrollers with USB
• Manufacturer: Microchip Technology

13.4
13.4.1
A Power-on Reset pulse is generated on-chip when
V
take advantage of the POR, just tie the MCLR pin
directly (or through a resistor) to V
nate external RC components usually needed to create
a POR. A maximum rise time for V
Electrical Specifications for details.
When the device starts normal operation (exits the
reset condition), device operating parameters (voltage,
frequency, temperature) must be met to ensure opera-
tion. If these conditions are not met, the device must be
held in reset until the operating conditions are met.
Brown-out reset may be used to meet the startup con-
ditions.
For additional information, refer to Application Note
AN607, “ Power-up Trouble Shooting .”
13.4.2
The Power-up Timer provides a fixed 72 ms nominal
time-out on power-up from the POR. The PWRT oper-
ates on an internal RC oscillator. The device is kept in
reset as long as the PWRT is active. The PWRT’s time
delay allows V
figuration bit is provided to enable/disable the PWRT.
The power-up time delay will vary from chip to chip due
to V
parameters for details (T
13.4.3
The Oscillator Start-up Timer provides a delay of 1024
oscillator cycles (from OSC1 input) after the PWRT
delay. This ensures that the crystal oscillator or resona-
tor has started and stabilized.
The OST time-out is invoked only for HS mode and only
on power-on reset or wake-up from SLEEP.
DD
1999 Microchip Technology Inc.
DD
rise is detected (in the range of 1.5V - 2.1V). To
, temperature and process variation. See DC
Resets
POWER-ON RESET (POR)
POWER-UP TIMER (PWRT)
OSCILLATOR START-UP TIMER (OST)
DD
to rise to an acceptable level. A con-
PWRT
, parameter #33).
DD
DD
is specified. See
. This will elimi-
Advanced Information
13.4.4
If V
than T
will reset the device. If V
than T
Once the brown-out occurs, the device will remain in
brown-out reset until V
power-up timer then keeps the device in reset for
T
during T
when V
reset. Since the device is intended to operate at 5V
nominal only, the brown-out detect is always enabled
and the device will reset when Vdd falls below the
brown-out threshold. This device is unique in that the
4 WDT timer will not activate after a brown-out if
PWRTE = 1 (inactive).
13.4.5
On power-up, the time-out sequence is as follows: The
PWRT delay starts (if enabled) when a POR reset
occurs. Then OST starts counting 1024 oscillator
cycles when PWRT ends (HS). When the OST ends,
the device comes out of RESET.
If MCLR is kept low long enough, the time-outs will
expire. Bringing MCLR high will begin execution imme-
diately. This is useful for testing purposes or to synchro-
nize more than one PIC16CXX device operating in
parallel.
Table 13-5 shows the reset conditions for the STATUS,
PCON and PC registers, while Table 13-7 shows the
reset conditions for all the registers.
13.4.6
The Brown-out Reset Status bit, BOR, is unknown on a
POR. It must be set by the user and checked on subse-
quent resets to see if bit BOR was cleared, indicating a
BOR occurred. The BOR bit is not predictable if the
brown-out reset circuitry is disabled.
The Power-on Reset Status bit, POR, is cleared on a
POR and unaffected otherwise. The user must set this
bit following a POR and check it on subsequent resets
to see if it has been cleared.
PWRT
DD
BOR
BOR
falls below V
(parameter #33). If V
DD
PWRT
BROWN-OUT RESET (BOR)
TIME-OUT SEQUENCE
POWER CONTROL/STATUS REGISTER
(PCON)
, a reset may not occur.
rises above V
(parameter #35), the brown-out situation
, the brown-out reset process will restart
PIC16C745/765
BOR
(parameter D005) for longer
DD
BOR
DD
DD
falls below V
rises above V
with the power-up timer
should fall below V
DS41124A-page 99
BOR
BOR
for less
. The
BOR