MT9122 Zarlink Semiconductor, MT9122 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
MT9122
Manufacturer Part Number
MT9122
Description
Dual Voice Echo CANceller (ITU-T G165 Compliant) With Disable Tone Detection
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT9122.pdf
(31 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT9122AP
Manufacturer:
MITEL
Quantity:
5 510
Company:
Part Number:
MT9122AP
Manufacturer:
AMI
Quantity:
5 510
Part Number:
MT9122AP
Manufacturer:
MITEL
Quantity:
20 000
Company:
Part Number:
MT9122AP1
Manufacturer:
AIMTEC
Quantity:
3 000
Company:
Part Number:
MT9122AP1
Manufacturer:
ZARLINK
Quantity:
9
Company:
Part Number:
MT9122AS
Manufacturer:
MITEL
Quantity:
76
MT9122
Pin Description (continued)
Notes:
1. All unused inputs should be connected to logic low or high unless otherwise stated. All outputs should be left open circuit when not used.
2. All inputs have TTL compatible logic levels except for MCLK, Sin and Rin pins which have CMOS compatible logic levels and PWRDN
3. All outputs are CMOS pins with CMOS logic levels.
4
17/18
19/20
27/28 CONFIG1/
Pin #
pin which has Schmitt trigger compatible logic levels.
17
18
19
20
21
22
23
24
25
26
CONFIG2
BCLK/C4i Bit Clock/ST-BUS Clock (Input):
DATA2
DATA1
Name
S4/S3
SCLK
S2/S1
F0od
Sout
Rout
VDD
CS
F0i
Selection of Echo Canceller B Functional States (Input):
Controllerless Mode: Selects Echo Canceller B functional states according to Table 2.
Controller Mode: S4 and S3 pins become SCLK and CS pins respectively.
Serial Port Synchronous Clock (Input): Data clock for the serial microport interface.
Chip Select (Input): Enables serial microport interface data transfers. Active low.
Selection of Echo Canceller A Functional States (Input):
Controllerless Mode: Selects Echo Canceller A functional states according to Table 2.
Controller Mode: S2 and S1 pins become DATA2 and DATA1 pins respectively.
Serial Data Receive (Input):
In Motorola/National serial microport operation, the DATA2 pin is used for receiving data. In
Intel serial microport operation, the DATA2 pin is not used and must be tied to Vss or Vdd.
Serial Data Port (Bidirectional):
In Motorola/National serial microport operation, the DATA1 pin is used for transmitting data. In
Intel serial microport operation, the DATA1 pin is used for transmitting and receiving data.
Delayed Frame Pulse Output (Output):
In ST-BUS operation, this pin generates a delayed frame pulse after the 4th channel time slot
and is used for daisy-chaining multiple ST-BUS devices. See Figures 5 to 8.
In SSI operation, this pin outputs logic low.
Positive Power Supply: Nominally 5 volts.
Send PCM Signal Output (Output):
128 kbit/s to 4096 kbit/s serial PCM output stream. Data may be in either companded or 2’s
complement linear PCM format. Two PCM channels are time-multiplexed on this pin. These
are the Send Out signals after echo cancellation and Non-linear processing. Data bits are
clocked out following SSI or ST-BUS timing requirements.
Receive PCM Signal Output (Output):
128 kbit/s to 4096 kbit/s serial PCM output stream. Data may be in either companded or 2’s
complement linear PCM format. Two PCM channels are time-multiplexed on this pin. This
output pin is provided for convenience in some applications and may not always be required.
Data bits are clocked out following SSI or ST-BUS timing requirements.
Frame Pulse (input):
In ST-BUS operation, this is a frame alignment low going pulse. SSI operation is enabled by
connecting this pin to Vss.
In SSI operation, BCLK pin is a 128 kHz to 4.096 MHz bit clock. This clock must be
synchronous with ENA1, ENA2, ENB1 and ENB2 enable strobes.
In ST-BUS operation, C4i pin must be connected to the 4.096MHz (C4) system clock.
Device Configuration Pins (Inputs).
When CONFIG1 and CONFIG2 pins are both logic 0, the MT9122 serial microport is enabled.
This configuration is defined as Controller Mode. When CONFIG1 and CONFIG2 pins are in
any other logic combination, the MT9122 is configured in Controllerless Mode. See Table 3.
Description
Data Sheet