MAX186 Maxim, MAX186 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
MAX186
Manufacturer Part Number
MAX186
Description
Low-Power / 8-Channel / Serial 12-Bit ADCs
Manufacturer
Maxim
Datasheet
1.MAX186.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX1864EEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1864TEEE
Manufacturer:
MAXIM
Quantity:
81
Part Number:
MAX1864TEEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1864TEEE-T
Manufacturer:
ANPEC
Quantity:
3 400
Part Number:
MAX1865EEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1865TEEP
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1865TEEP+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Part Number:
MAX1866EUB
Manufacturer:
MAXIM/美信
Quantity:
20 000
Figure 15. MAX186/MAX188 Unipolar Transfer Function,
4.096V = Full Scale
Using the buffered REFADJ input avoids external
buffering of the reference. To use the direct VREF input,
disable the internal buffer by tying REFADJ to V
Figure 15 depicts the nominal, unipolar input/output
(I/O) transfer function, and Figure 16 shows the bipolar
input/output transfer function. Code transitions occur
halfway between successive integer LSB values. Output
coding is binary with 1 LSB = 1.00mV (4.096V/4096) for
unipolar operation and 1 LSB = 1.00mV ((4.096V/2 -
-4.096V/2)/4096) for bipolar operation.
Figure 17, the MAX186 Reference-Adjust Circuit, shows
how to adjust the ADC gain in applications that use the
internal reference. The circuit provides ±1.5%
(±65LSBs) of gain adjustment range.
For best performance, use printed circuit boards.
Wire-wrap boards are not recommended. Board layout
should ensure that digital and analog signal lines are
separated from each other. Do not run analog and digi-
tal (especially clock) lines parallel to one another, or
digital lines underneath the ADC package.
Figure 18 shows the recommended system ground
connections. A single-point analog ground (“star”
ground point) should be established at AGND, sepa-
rate from the logic ground. All other analog grounds
11 . . . 111
11 . . . 110
00 . . . 011
00 . . . 010
11 . . . 101
00 . . . 001
00 . . . 000
OUTPUT CODE
0
Transfer Function and Gain Adjust
1
Layout, Grounding, Bypassing
INPUT VOLTAGE (LSBs)
2
______________________________________________________________________________________
3
FULL-SCALE
TRANSITION
FS - 3/2LSB
1LSB = FS
FS = +4.096V
FS
DD
4096
.
and DGND should be connected to this ground. No
other digital system ground should be connected to
this single-point analog ground. The ground return to
the power supply for this ground should be low imped-
ance and as short as possible for noise-free operation.
High-frequency noise in the V
affect the high-speed comparator in the ADC. Bypass
these supplies to the single-point analog ground with
0.1µF and 4.7µF bypass capacitors close to the
MAX186/MAX188. Minimize capacitor lead lengths for
best supply-noise rejection. If the +5V power supply is
very noisy, a 10Ω resistor can be connected as a low-
pass filter, as shown in Figure 18.
Figure 16. MAX186/MAX188 Bipolar Transfer Function,
±4.096V/2 = Full Scale
Figure 17. MAX186 Reference-Adjust Circuit
Low-Power, 8-Channel,
011 . . . 111
011 . . . 110
000 . . . 010
000 . . . 001
000 . . . 000
111 . . . 111
111 . . . 110
111 . . . 101
100 . . . 001
100 . . . 000
100k
Serial 12-Bit ADCs
+5V
24k
-FS
1LSB = +4.096
FS = +4.096
2
4096
510k
0.01µF
INPUT VOLTAGE (LSBs)
DD
12
0V
power supply may
MAX186
REFADJ
+FS - 1LSB
19