ACS8526LC Semtech Corporation, ACS8526LC Datasheet - Page 61
![no-image](/images/manufacturer_photos/0/5/596/semtech_corporation_sml.jpg)
ACS8526LC
Manufacturer Part Number
ACS8526LC
Description
Line Card Protection Switch for PDH, Sonet or SDH Systems
Manufacturer
Semtech Corporation
Datasheet
1.ACS8526LC.pdf
(74 pages)
- Current page: 61 of 74
- Download datasheet (604Kb)
JTAG
The JTAG connections on the ACS8526 allow a full
boundary scan to be made. The JTAG implementation is
fully compliant to IEEE 1149.1
exceptions, and the user should refer to the standard for
further information.
1. The output boundary scan cells do not capture data
2. In common with some other manufacturers, pin TRST
The JTAG timing diagram is shown in Figure 9.
Figure 9 JTAG Timing
Table 18 JTAG Timing (for use with Figure 9)
Revision 4.01/June 2006 © Semtech Corp.
Electrical Specifications
ADVANCED COMMUNICATIONS
Cycle Time
TMS/TDI to TCK rising edge time
TCK rising to TMS/TDI hold time
TCK falling to TDO valid
from the core, and so do not support INTEST. However
this does not affect board testing.
is internally pulled Low to disable JTAG by default. The
standard is to pull High. The polarity of TRST is as the
standard: TRST High to enable JTAG boundary scan
mode, TRST Low for normal operation.
Parameter
TCK
TMS
TDO
TDI
[4]
, with the following minor
t
SUR
Symbol
t
t
t
t
DOD
SUR
CYC
HT
t
HT
FINAL
Page 61
Minimum
50
23
3
Over-voltage Protection
The ACS8526 may require Over-voltage Protection on
input reference clock ports according to ITU
recommendation K.41
are recommended for this purpose (see separate
Semtech data book).
ESD Protection
Suitable precautions should be taken to protect against
electrostatic damage during handling and assembly. This
device incorporates ESD protection structures that
protect the device against ESD damage at ESD input
levels up to at least +/2kV using the Human Body Model
(HBD) MIL-STD-883D Method 3015.7, for all pins.
Latchup Protection
This device is protected against latchup for input current
pulses of magnitude up to at least ±100 mA to JEDEC
Standard No. 78 August 1997.
-
t
CYC
t
DOD
Typical
-
-
-
-
ACS8526 LC/P LITE
[10]
F8110D_022JTAGTiming_01
. Semtech protection devices
Maximum
5
-
-
-
DATASHEET
www.semtech.com
Units
ns
ns
ns
ns
Related parts for ACS8526LC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ACS-1024-LG](/images/no-image3.png)
Part Number:
Description:
Image Sensor, CMOS|CCD, 1026x1026 Pixels, 132pin LCC
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-I1024-CPGA](/images/no-image3.png)
Part Number:
Description:
High Performance Area CMOS Image Sensor
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-I2048-CPGA](/images/no-image3.png)
Part Number:
Description:
Image Sensor, CMOS, 2048x2048 Pixels, 144pin CPGA
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-C018](/images/no-image3.png)
Part Number:
Description:
SMD Mini Spring Coils
Manufacturer:
ECM [ECM Electronics Limited.]
Datasheet:
![6666](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1084CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1587CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
![ACS8515](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SR3.3](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
![SC1151CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: