ACS00MS Intersil Corporation, ACS00MS Datasheet - Page 8

• Manufacturer Part Number: ACS00MS
• Description: Radiation Hardened Quad 2-input NAND Gate
• Manufacturer: Intersil Corporation

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
7585 Irvine Center Drive
Suite 100
Irvine, CA 92618
TEL: [phone]
FAX: [phone]
Ceramic Metal Seal Flatpack Packages (Flatpack)
NOTES:
b
1. Index area: A notch or a pin one identification mark shall be locat-
2. If a pin one identification mark is used in addition to a tab, the lim-
3. This dimension allows for off-center lid, meniscus, and glass overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
A
SEATING AND
BASE PLANE
e
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
its of dimension k do not apply.
M applies to lead plating and finish thickness. The maximum lim-
its of lead dimensions b and c or M shall be measured at the cen-
troid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
-C-
-A-
0.004
Q
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
M
H A - B
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
L
M
For information regarding Intersil Corporation and its products, see www.intersil.com
c1
S
E3
SECTION A-A
D
LEAD FINISH
S
METAL
BASE
Intersil Corporation
2401 Palm Bay Rd.
Palm Bay, FL 32905
TEL: [phone]
FAX: [phone]
b1
(b)
E1
E2
PIN NO. 1
ID AREA
E
M
E3
0.036
(c)
M
-D-
L
H A - B
S1
C
-B-
S
A
A
D
ACS00MS
-H-
S
D
EUROPE
Intersil Europe Sarl
Ave. William Graisse, 3
1006 Lausanne
Switzerland
TEL: [phone]
FAX: [phone]
8
K14.A
14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
10. Controlling dimension: INCH.
SYMBOL
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric mate-
8. Dimension Q shall be measured at the point of exit (beyond the
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
b1
E1
E2
E3
S1
rials shall be molded to the bottom of the package to cover the
leads.
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when sol-
der dip lead finish is applied.
c1
M
D
Q
N
A
b
E
e
L
c
k
MIL-STD-1835 CDFP3-F14 (F-2A, CONFIGURATION B)
0.045
0.015
0.015
0.004
0.004
0.235
0.125
0.030
0.008
0.270
0.026
0.005
MIN
-
-
-
0.050 BSC
INCHES
14
0.115
0.022
0.019
0.009
0.006
0.390
0.260
0.290
0.015
0.370
0.045
0.0015
MAX
ASIA
Intersil Corporation
Unit 1804 18/F Guangdong Water Building
83 Austin Road
TST, Kowloon Hong Kong
TEL: [phone]
FAX: [phone]
-
-
-
1.14
0.38
0.38
0.10
0.10
5.97
3.18
0.76
0.20
6.86
0.66
0.13
MIN
MILLIMETERS
-
-
-
1.27 BSC
Spec Number
14
2.92
0.56
0.48
0.23
0.15
9.91
6.60
7.11
0.38
9.40
1.14
0.04
MAX
-
-
-
Rev. 0 5/18/94
NOTES
518813
3
3
7
2
8
6
-
-
-
-
-
-
-
-
-
-
-