IL6083 IK Semicon Co., Ltd, IL6083 Datasheet
IL6083
Related parts for IL6083
IL6083 Summary of contents
Page 1
... Pin Symbol 01 Supply voltage ground GND 03 Control input (duty cycle Oscillator Osc 05 Short-circuit protection delay Delay 06 Current sensing Sense 07 Voltage doubler 2Vs 08 Output Output Pin Configuration Figure 1. Pin Description TECHNICAL DATA IL6083 IL6083N DIP –40 ~ +110°С A Rev. 00 ...
Page 2
... Supply voltage Vbatt Storage temperature Tstg С Ambient operation temperature range T Junction maximum temperature TJ(max), Temperature resistance junction – ambient Rth j-a, =120 Figure 2. Maximum Ratings min max 9 -40 +110 C/W IL6083 Absolute Maximum Ratings min Max 32.5 -55 +125 -55 +125 +150 Rev. 00 ...
Page 3
... Functional Description Batt is calculated as follows: lamp < 5.0 V, the external FET is switched off and the latch for Batt and R (see Figure 4). 2 and ground (V ≤ 16.5 V). Batt IL6083 = The gate of the S ≥ 5.4 V. Batt = 13 V. Pin thus 2 Rev. 00 ...
Page 4
... Hz as shown in the data sheet α α α 0.7, α = 0.67 and α (see Figure 4) 4 For a duty cycle of less than 100%, the 4 . (see “Output Slope Control” possible to have a range of oscillator frequencies from IL6083 = 0.28 . From 9 to 16,5V. batt Rev. 00 ...
Page 5
... VDE 0879 part 3/4.81 • Test conditions refering to Figure 3 • Application circuit according to Figure 1 or Figure 4 • Load: nine 4 W lamps in parallel • Duty cycle = 18% • Batt • 100 Hz Osc Figure 3. Voltage Spectrum of On-board Radio Reception IL6083 is recommended. 4 Rev. 00 ...
Page 6
... The external FET again is switched off after the cut- ch dis is not charged by parasitic currents. 5 ≈ 10 mV, it ensures that current limitation occurs only - ≈ 400 kHz) and a voltage doubler circuit. This 7 IL6083 (bootstrapping). In addition, a Rev. 00 ...
Page 7
... I dis dis Voltage doubler, Pin 7 V Duty cycle 100 =5mA (whichever is lower /dt =α α /dt 8 max IL6083 Rate Unit min Typ. max 7 24.5 27.0 V 4.4 5.0 5.6 V 4.8 5.4 6.0 18.3 20.0 21.7 V 16.7 18.5 20.3 25.5 28.5 32.5 V 19.5 23.0 26.5 18.5 20.0 21 100 120 105 ...
Page 8
... V = high level >| Min: С =68nF 2 Max: V ≤12.4V, batt V = 16.5V, batt С =68nF 2 Oscillator, Pin 4 V =12.0 V batt С is open, 4 С =68nF, duty cycle=50% 2 IL6083 Rate Unit min Type max 0.35 0.70 0.95 1. 1 100 % 2000 Hz 0.68 0.7 0.72 0.65 0.67 0.69 0.26 0.28 0 ...
Page 9
... Application Circuit Figure 4. Application Circuit IL6083 Rev. 00 ...
Page 10
... F C SEATING -T- PLANE 0.25 (0.010 NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. DIP-8 N SUFFIX PLASTIC DIP (MS – 001BA IL6083 Dimension, mm Symbol MIN MAX A 8.51 10.16 6.1 7. 5.33 D 0.36 0.56 1.14 1. 2.54 H 7.62 0° ...