PAD112 Thaler Corporation, PAD112 Datasheet - Page 3

• Manufacturer Part Number: PAD112
• Description: High Voltage Operational Amplifier
• Manufacturer: Thaler Corporation

PAD112
__________________________________________________________________________________
SUPPLY VOLTAGE, +HV to −HV
SUPPLY VOLTAGE, +Vcc to −Vcc
SUPPLY VOLTAGE, +Vcc
SUPPLY VOLTAGE, −Vcc
OUTPUT CURRENT, peak
POWER DISSIPATION, internal, DC 50W
INPUT
OFFSET VOLTAGE
OFFSET VOLTAGE vs. temperature
OFFSET VOLTAGE vs. supply
BIAS CURRENT, initial
BIAS CURRENT vs. supply
OFFSET CURRENT, initial
INPUT RESISTANCE, DC
INPUT CAPACITANCE
COMMON MODE VOLTAGE RANGE
COMMON MODE VOLTAGE RANGE
COMMON MODE REJECTION, DC
NOISE
GAIN
OPEN LOOP
GAIN BANDWIDTH PRODUCT @ 1MHz
PHASE MARGIN
OUTPUT
VOLTAGE SWING
VOLTAGE SWING
CURRENT, continuous, DC
SLEW RATE, A
SETTLING TIME, to 0.1%
RESISTANCE
POWER SUPPLY
VOLTAGE
CURRENT, quiescent
CURRENT, shutdown, pin 7 low
THERMAL
RESISTANCE, AC, junction to air
RESISTANCE, DC junction to air, outputs
TEMPERATURE RANGE, heat sink
FAN, 40mm dc brushless, ball bearing
OPERATING VOLTAGE
OPERATING CURRENT
AIR FLOW
RPM
NOISE
L10, life expectancy, 50
L10, life expectancy, 25
NOTES:
1. Unless otherwise noted: T
2. Derate internal power dissipation to achieve high MTBF.
3. Doubles for every 10
4. +HV and −HV denote the positive and negative supply voltages to the output stage. +Vcc and −Vcc denote the positive and negative supply voltages to
the input stages.
5. Limited by fan characteristics. During operation, even though the heat sink may be at 85
6. Rating applies if the output current alternates between both output transistors at a rate faster than 60Hz.
7. Power supply voltages +Vcc and −Vcc must not be less than +HV and −HV respectively. Total voltage +Vcc to −Vcc 150V maximum.
8. L10 refers to the time it takes for 10% of a population of fans to fail. Lower ambient temperature increases fan life.
Thaler Corp 2015 N Forbes Blvd Tucson AZ 85745 USA Phone [phone] or [phone] Fax [phone] Web Site:
PARAMETER
V
= −10
O
O
O
3
C
C
C of case temperature increase.
HIGH VOLTAGE OPERATIONAL AMPLIFIER
8
8
C
= 25
6
O
C, compensation Cc = 470pF, DC input specifications are ± value given, power supply voltage is typical rating.
150V
150V
+HV+15V
−HV-15V
10A, within SOA
Full temperature range
100kHz bandwidth, 1kΩ R
R
C
Full temperature range
I
I
C
2V Step, C
No load, DC
Full temperature range, f 60Hz
Full temperature range
O
O
L
C
C
= 10kΩ, C
= 5A
= −5A
=100pF
= 100pF
TEST CONDITIONS
7
7
ABSOLUTE MAXIMUM RATINGS
C
= 100pF
C
=100pF
≥
S
1
DIFFERENTIAL INPUT VOLTAGE
TEMPERATURE, junction
INPUT VOLTAGE
TEMPERATURE, pin solder, 10s
OPERATING TEMPERATURE, heat sink −40 to 105°C
TEMPERATURE RANGE, storage
+HV−7
−HV+7
MIN
± 15
−40
110
108
45
11
O
C or more the fan will be at a lower temperature.
ABSOLUTE MAXIMUM RATINGS
+HV−6
−HV+6
TYP
7000
100
128
± 50
1.2
7.5
20
10
14
18
12
50
30
45
60
1
4
2
6
8
2
+Vcc−15
−Vcc+7
MAX
100
± 75
105
0.1
1.7
2.7
50
20
50
22
3
5
2
SPECIFICATIONS
mV
μV/
μV/V
pA
pA/V
pA
G Ω
pF
V
V
dB
μV RMS
dB
MHz
degree
V
V
A
V/μS
μS
Ω
V
mA
mA
O
O
O
V
mA
CFM
RPM
dB
kHrs
kHrs
+Vcc to −Vcc
C/W
C/W
C
−40 to 70°C
UNITS
O
C
300°C
175°C
±
20V
www.Thaler.com
5
3