IXDN402 IXYS Corporation, IXDN402 Datasheet - Page 9

• Manufacturer Part Number: IXDN402
• Description: 2 Ampere Dual Low-Side Ultrafast MOSFET Drivers
• Manufacturer: IXYS Corporation

PIN CONFIGURATIONS
Supply Bypassing, Grounding Practices And Output Lead inductance
When designing a circuit to drive a high speed MOSFET
utilizing the IXDN402/IXDI402/IXDF402, it is very important to
observe certain design criteria in order to optimize performance
of the driver. Particular attention needs to be paid to Supply
Bypassing, Grounding, and minimizing the Output Lead
Inductance.
Say, for example, we are using the IXDN402 to charge a 1500pF
capacitive load from 0 to 25 volts in 25ns.
Using the formula: I= V C / t, where V=25V C=1500pF &
in 25ns will take a constant current of 1.5A. (In reality, the
charging current won’t be constant, and will peak somewhere
around 2A).
SUPPLY BYPASSING
In order for our design to turn the load on properly, the IXDN402
must be able to draw this 1.5A of current from the power supply
in the 25ns. This means that there must be very low impedance
between the driver and the power supply. The most common
method of achieving this low impedance is to bypass the power
supply at the driver with a capacitance value that is an order of
magnitude larger than the load capacitance. Usually, this
would be achieved by placing two different types of bypassing
capacitors, with complementary impedance curves, very close
to the driver itself.
selected and should have low inductance, low resistance and
high-pulse current-service ratings). Lead lengths may radiate
at high frequency due to inductance, so care should be taken
to keep the lengths of the leads between these bypass
capacitors and the IXDN402 to an absolute minimum.
t=25ns, we can determine that to charge 1500pF to 25 volts
4
1
2
3
4
6
1
2
3
5
7
8
8 Lead PDIP (PI)
8 Pin SOIC (SI)
NC
GND
GND
IN A
GND
INB
NC
IN A
NC
NC
NC
IN B
IXDN402SI-16
16 Pin SOIC
IXDN402
OUT A
OUT A
OUT B
OUT A
OUT B
OUT B
VCC
VCC
NC
NC
NC
V
(These capacitors should be carefully
S
16
15
14
13
12
10
11
5
8
7
6
9
2
3
4
1
1
2
3
4
5
6
7
8
8 Lead PDIP (PI)
8 Pin SOIC (SI)
NC
IN A
GND
INB
GND
GND
NC
IN A
NC
NC
NC
IN B
16 Pin SOIC
IXDI402SI-16
IXDI402
OUT A
OUT B
OUT A
OUT A
OUT B
OUT B
VCC
VCC
9
NC
NC
NC
V
S
GROUNDING
In order for the design to turn the load off properly, the IXDN402
must be able to drain this 1.5A of current into an adequate
grounding system. There are three paths for returning current
that need to be considered: Path #1 is between the IXDN402
and its load. Path #2 is between the IXDN402 and its power
supply. Path #3 is between the IXDN402 and whatever logic is
driving it. All three of these paths should be as low in resistance
and inductance as possible, and thus as short as practical. In
addition, every effort should be made to keep these three
ground paths distinctly separate.
ground current from the load may develop a voltage that would
have a detrimental effect on the logic line driving the IXDN402.
OUTPUT LEAD INDUCTANCE
Of equal importance to Supply Bypassing and Grounding are
issues related to the Output Lead Inductance. Every effort
should be made to keep the leads between the driver and its
load as short and wide as possible. If the driver must be placed
farther than 2” (5mm) from the load, then the output leads
should be treated as transmission lines. In this case, a twisted-
pair should be considered, and the return line of each twisted
pair should be placed as close as possible to
of the driver, and connected directly to the ground terminal
of the load.
8
6
5
7
16
15
14
13
12
10
11
9
IXDN402 / IXDI402 / IXDF402
1
2
3
4
1
2
3
4
5
6
7
8
8 Lead PDIP (PI)
8 Pin SOIC (SI)
NC
IN A
GND
INB
GND
GND
NC
IN A
NC
NC
NC
IN B
Otherwise, the returning
16 Pin SOIC
IXDF402SI-16
IXDF402
OUT A
OUT B
OUT A
OUT A
OUT B
OUT B
VCC
VCC
NC
the ground pin
NC
NC
V
S
8
6
5
7
16
15
14
13
12
10
11
9