TLE 7279-2G V33 Infineon Technologies, TLE 7279-2G V33 Datasheet
TLE 7279-2G V33
Specifications of TLE 7279-2G V33
Related parts for TLE 7279-2G V33
TLE 7279-2G V33 Summary of contents
Page 1
...
Page 2
Low Dropout Voltage Regulator 1 Overview Features • Output voltage 2.6 V • Output voltage tolerance 2% • Output current up to 180 mA • Ultra low quiescent current consumption < • Enable ...
Page 3
Pin Configuration 2.1 Pin Assignment (PG-DSO-14) Figure 1 Pin Configuration 2.2 Pin Definitions and Functions (PG-DSO-14) Pin Symbol Function 1 RO Reset Output TLE7279-2GV33, TLE7279-2GV26: open drain output; TLE7279-2GV50: integrated 20 k leave open if Reset is not needed ...
Page 4
Pin Assignment (PG-SSOP-14 Exposed Pad) Figure 2 Pin Configuration 2.4 Pin Definitions and Functions (PG-SSOP-14 Exposed Pad) Pin Symbol Function 1 RO Reset Output integrated 20 k leave open if Reset is not needed 2, 5 GND Ground connect ...
Page 5
Block Diagram I Bandgap Reference Charge Pump EN Enable SI Figure 3 Block Diagram Data Sheet TLE7279-2 Overtemperature shutdown 1 GND 5 TLE7279-2 Block Diagram Q RO Reset Generator RM SO Rev. 1.2, 2008-05-08 ...
Page 6
General Product Characteristics 4.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings +150 C; all voltages with respect to ground, positive current flowing into pin j (unless otherwise specified) Pos. Parameter Input I, Sense Input ...
Page 7
Functional Range Pos. Parameter 4.2.1 Input voltage 4.2.2 4.2.3 4.2.4 Output capacitor’s requirements for Stability 4.2.5 Junction temperature 1) the minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30 relevant ESR value ...
Page 8
Block Description and Electrical Characteristics 5.1 Circuit Description 5.1.1 Power On Reset and Reset Output V For an output voltage level the signal at RO remains low for the power-up reset delay time RT in Figure ...
Page 9
Early Warning The additional sense comparator provides an early warning function: Any voltage (e.g. the input voltage) can be monitored, an undervoltage condition is indicated by setting the comparator’s output to low. See Sense Input Voltage V SI, High ...
Page 10
Electrical Characteristics Electrical Characteristics 13 - +150 C, all voltages with respect to ground, positive current flowing into pin I j (unless otherwise specified) Pos. Parameter Output Q 5.2.1 Output voltage 5.2.2 ...
Page 11
Electrical Characteristics (cont’ +150 C, all voltages with respect to ground, positive current flowing into pin I j (unless otherwise specified) Pos. Parameter 5.2.16 Low Level Input Voltage 5.2.17 5.2.18 High ...
Page 12
Electrical Characteristics (cont’ +150 C, all voltages with respect to ground, positive current flowing into pin I j (unless otherwise specified) Pos. Parameter Reset Output RO 5.2.33 Output Undervoltage Reset Switching ...
Page 13
Electrical Characteristics (cont’ +150 C, all voltages with respect to ground, positive current flowing into pin I j (unless otherwise specified) Pos. Parameter 5.2.47 Power-on reset delay time 5.2.48 Reset Reaction ...
Page 14
Typical Performance Characteristics I Current Consumption versus q T Junction Temperature (EN=ON [µ 13.5V I 100 I = 100 µ 0.01 -40 - Current Consumption versus q ...
Page 15
Typical Performance Characteristics (cont´d) V Load Regulation d versus Q I Output Current Change [mV ° -40 ° 150 ° ...
Page 16
Typical Performance Characteristics (cont´d) V Line Regulation d versus Q V Input Voltage Change [mV 100mA 10mA 1mA ...
Page 17
Typical Performance Characteristics (cont´d) I Enable Input Current versus EN V Input Voltage , EN=Off [µ OFF 1.0 0.8 0 150° 25°C 0 Reset Threshold ...
Page 18
Typical Performance Characteristics (cont´d) V Reset Threshold versus RT T Junction Temperature (3.3V-Version [V] Q 3.20 Reset Release Threshold 3.10 3.00 Reset Trigger Threshold 2.90 -40 - Reset Threshold versus RT T Junction ...
Page 19
Typical Performance Characteristics (cont´d) t Reset Delay Time versus RD T Junction Temperature [ms] 40 SLOW Timing 30 20 FAST Timing 10 -40 - Reset Output Sink Current RO T Junction ...
Page 20
Package Outlines 1.27 +0.10 2) 0.41 -0. 8.75 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area Figure 6 PG-DSO-14 (Plastic/Plastic ...
Page 21
4.9 ±0.1 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not include dambar protrusion Figure 7 PG-SSOP-14 Exposed Pad ...
Page 22
Revision History Revision Date Changes 1.2 2009-05-08 2.6V version, 5V version in PG-SSOP-14 package and all related description added drawing for PG-SSOP-14 added In TLE7279-2EV50” added In description for Pin 1 and Pin 7 “, TLE7273-2GV26” added ...
Page 23
Revision Date Changes In external pull-up resistor at RO added In added: Item 1.0 2008-04-10 final version data sheet Data Sheet “Power On Reset and Reset Output” on Page 8 “Electrical Characteristics” on Page 10 Item 5.2.3, Item 5.2.4, Item ...
Page 24
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...