TMP86xy09NG Toshiba, TMP86xy09NG Datasheet - Page 69

• Manufacturer Part Number: TMP86xy09NG
• Manufacturer: Toshiba

Specifications of TMP86xy09NG

• Package: SDIP32
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 8/16
• Ram Size: 256/512
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 1
• I2c/sio Channels: -
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 6
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 1
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: √
• Dual Clock: √
• Clock Gear: -
• Number Of I/o Ports: 26
• Power Supply (v): 2.7 to 5.5

Watchdog Timer Control Register 1
Watchdog Timer Control Register 2
7.2.2 Watchdog Timer Enable
WDTCR1
WDTCR2
(0034H)
(0035H)
Note 1: After clearing WDTOUT to “0”, the program cannot set it to “1”.
Note 2: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *: Don’t care
Note 3: WDTCR1 is a write-only register and must not be used with any of read-modify-write instructions. If WDTCR1 is read, a
Note 4: To activate the STOP mode, disable the watchdog timer or clear the counter immediately before entering the STOP mode.
Note 5: To clear WDTEN, set the register in accordance with the procedures shown in “1.2.3 Watchdog Timer Disable”.
to “1” during reset, the watchdog timer is enabled automatically after the reset release.
Note 1: The disable code is valid only when WDTCR1<WDTEN> = 0.
Note 2: *: Don’t care
Note 3: The binary counter of the watchdog timer must not be cleared by the interrupt task.
Note 4: Write the clear code 4EH using a cycle shorter than 3/4 of the time set in WDTCR1<WDTT>.
Setting WDTCR1<WDTEN> to “1” enables the watchdog timer. Since WDTCR1<WDTEN> is initialized
WDTOUT
don’t care is read.
After clearing the counter, clear the counter again immediately after the STOP mode is inactivated.
WDTEN
WDTCR2
WDTT
7
7
Watchdog timer enable/disable
Watchdog timer detection time
[s]
Watchdog timer output select
6
Write
Watchdog timer control code
6
5
(ATAS)
5
4
(ATOUT)
4
0: Disable (Writing the disable code to WDTCR2 is required.)
1: Enable
0: Interrupt request
1: Reset request
4EH: Clear the watchdog timer binary counter (Clear code)
B1H: Disable the watchdog timer (Disable code)
D2H: Enable assigning address trap area
Others: Invalid
3
00
01
10
11
WDTEN
Page 59
3
2
DV7CK = 0
2
2
2
2
25
23
19
21
2
/fc
/fc
/fc
fc
NORMAL1/2 mode
WDTT
1
1
DV7CK = 1
0
2
2
2
2
17
15
13
11
WDTOUT
/fs
/fs
/fs
/fs
(Initial value: **** ****)
0
(Initial value: **11 1001)
SLOW1/2
mode
2
2
2
2
17
11
15
13
/fs
/fs
fs
fs
TMP86C809NG
Write
Write
Write
only
only
only
Write
only