TDA9885TS/V5,118 NXP Semiconductors, TDA9885TS/V5,118 Datasheet - Page 10
![IC IF-PLL DEMOD I2C-BUS 24-SSOP](/photos/7/6/70618/ssop24_sot340-1_sml.jpg)
TDA9885TS/V5,118
Manufacturer Part Number
TDA9885TS/V5,118
Description
IC IF-PLL DEMOD I2C-BUS 24-SSOP
Manufacturer
NXP Semiconductors
Type
Demodulatorr
Datasheet
1.TDA9885HNV5118.pdf
(56 pages)
Specifications of TDA9885TS/V5,118
Package / Case
*
Applications
TV
Mounting Type
Surface Mount
Product
General Purpose Audio Amplifiers
Available Set Gain
66 dB
Thd Plus Noise
0.15 %, 0.5 %
Operating Supply Voltage
5 V
Supply Current
63 mA
Maximum Power Dissipation
305 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Audio Load Resistance
10 KOhms, 100 KOhms
Input Bias Current (max)
2 mA, 1.15 mA
Minimum Operating Temperature
- 20 C
Output Signal Type
Differential
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935286735118
TDA9885TS/V5-T
TDA9885TS/V5-T
TDA9885TS/V5-T
TDA9885TS/V5-T
NXP Semiconductors
TDA9885_TDA9886_3
Product data sheet
8.6 AFC and digital acquisition help
8.7 Video demodulator and amplifier
Each relaxation oscillator of the VIF-PLL and FM-PLL demodulator has a wide frequency
range. To prevent false locking of the PLLs and with respect to the catching range, the
digital acquisition help provides an individual control, until the frequency of the VCO is
within the preselected standard dependent lock-in window of the PLL.
The in-window and out-window control at the FM PLL is additionally used to mute the
audio stage (if auto mute is selected via the I
The working principle of the digital acquisition help is as follows. The PLL VCO output is
connected to a down counter which has a predefined start value (standard dependent).
The VCO frequency clocks the down counter for a fixed gate time. Thereafter, the down
counter stop value is analyzed. In case the stop value is higher (lower) than the expected
value range, the VCO frequency is lower (higher) than the wanted lock-in window
frequency range. A positive (negative) control current is injected into the PLL loop filter
and consequently the VCO frequency is increased (decreased) and a new counting cycle
starts.
The gate time as well as the control logic of the acquisition help circuit is dependent on the
precision of the reference signal at pin REF. Operation as a crystal oscillator is possible as
well as connecting this input via a serial capacitor to an external reference frequency, e.g.
the tuning system oscillator.
The AFC signal is derived from the corresponding down counter stop value after a
counting cycle. The last four bits are latched and can be read out via the I
(see
The video demodulator is realized by a multiplier which is designed for low distortion and
large bandwidth. The VIF signal is multiplied with the ‘in phase’ signal of the VIF-PLL
VCO.
The demodulator output signal is fed into the video preamplifier via a level shift stage with
integrated low-pass filter to achieve carrier harmonics attenuation.
The output signal of the preamplifier is fed to the VIF-AGC detector (see
in the sound trap mode also fed internally to the integrated sound carrier trap
(see
and amplified by the following post-amplifier. The video output level at pin CVBS is
2 V (p-p).
In the trap bypass mode the output signal of the preamplifier is fed directly through the
post-amplifier to pin CVBS. The output video level is 1.1 V (p-p) for using an external
sound trap with 10 % overall loss.
Noise clipping is provided in both cases.
Table
Section
8). Also the digital-to-analog converted value is given as current at pin AFC.
8.8). The differential trap output signal is converted to a single-ended signal
I
2
C-bus controlled multistandard alignment-free IF-PLL demodulators
Rev. 03 — 16 December 2008
2
C-bus).
TDA9885; TDA9886
© NXP B.V. 2008. All rights reserved.
Section
2
C-bus
8.3) and
10 of 56