ST7263BK6 STMicroelectronics, ST7263BK6 Datasheet - Page 139
ST7263BK6
Manufacturer Part Number
ST7263BK6
Description
LOW SPEED USB 8-BIT MCU FAMILY WITH UP TO 32K FLASH/ROM, DFU CAPABILITY, 8-BIT ADC, WDG, TIMER, SCI and I2C
Manufacturer
STMicroelectronics
Datasheet
1.ST7263BH6.pdf
(186 pages)
Specifications of ST7263BK6
4, 8, 16 Or 32 Kbytes Program Memory
high density Flash (HDFlash), FastROM or ROM with Read-Out and Write protection
- Current page: 139 of 186
- Download datasheet (3Mb)
ST7263Bxx
13.2
Note:
Figure 53. Pin input voltage
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Directly connecting the RESET and I/O pins to V
unintentional internal reset is generated or an unexpected change of the I/O configuration
occurs (for example, due to a corrupted program counter). To guarantee safe operation, this
connection has to be done through a pull-up or pull-down resistor (typical: 4.7 k
RESET, 10 k
according to their reset configuration.
Table 55.
1. Directly connecting the RESET and I/O pins to V
2. I
internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a
corrupted program counter). To guarantee safe operation, this connection has to be done through a pull-up
or pull-down resistor (typical: 4.7 kΩ for RESET, 10 kΩ for I/Os). Unused I/O pins must be tied in the same
way to VDD or VSS according to their reset configuration.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
INJ(PIN)
V
V
Symbol
V
ESD(HBM)
DD
IN
(1)(2)
- V
must never be exceeded. This is implicitly insured if V
SS
Ω
Voltage characteristics
for I/Os). Unused I/O pins must be tied in the same way to V
Supply voltage
Input voltage on true open drain pins
Input voltage on any other pin
Electrostatic discharge voltage (Human Body
model)
IN
>V
DD
while a negative injection is induced by V
Doc ID 7516 Rev 8
V
IN
Ratings
DD
or V
SS
ST7 PIN
DD
could damage the device if an unintentional
or V
IN
IN
maximum must always be respected.
maximum is respected. If V
SS
could damage the device if an
IN
<V
INJ(PIN)
V
Section 13.7.3
Maximum value
SS
Electrical characteristics
SS
V
. For true open-drain pads,
-0.3 to V
SS-
value. A positive
0.3 to 6.0
6.0
DD
DD
IN
+0.3
or V
maximum
Ω
for
SS
139/186
Unit
V
Related parts for ST7263BK6
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LOW SPEED USB 8-BIT MCU FAMILY with up to 16K MEMORY, up to 512 BYTES RAM, 8-BIT ADC, WDG, TIMER, SCI & I2C
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools ST7 Emulator Board
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: