STM8L151G2 STMicroelectronics, STM8L151G2 Datasheet - Page 72
STM8L151G2
Manufacturer Part Number
STM8L151G2
Description
STM8L-Ultra Low Power-8 bits Microcontrollers
Manufacturer
STMicroelectronics
Datasheet
1.STM8L151G2.pdf
(111 pages)
Specifications of STM8L151G2
Operating Power Supply
1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
Temperature Range
-40 to 85 or 125 °C
5 Low Power Modes
Wait, Low power run, Low power wait, Active-halt with RTC, Halt
Ultralow Leakage Per I/0
50 nA
Fast Wakeup From Halt
5 μs
Max Freq
16 MHz, 16 CISC MIPS peak
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM8L151G2U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
- Current page: 72 of 111
- Download datasheet (2Mb)
Electrical parameters
7.3.6
7.3.7
72/111
I/O current injection characteristics
As a general rule, current injection to the I/O pins, due to external voltage below V
above V
in order to give an indication of the robustness of the microcontroller in cases when
abnormal injection accidentally happens, susceptibility tests are performed on a sample
basis during device characterization.
Functional susceptibilty to I/O current injection
While a simple application is executed on the device, the device is stressed by injecting
current into the I/O pins programmed in floating input mode. While current is injected into the
I/O pin, one at a time, the device is checked for functional failures.
The failure is indicated by an out of range parameter: ADC1 error, out of spec current
injection on adjacent pins or other functional failure (for example reset, oscillator frequency
deviation, etc.).
The test results are given in the following table.
Table 33. I/O current injection susceptibility
I/O port pin characteristics
General characteristics
Subject to general operating conditions for V
unused pins must be kept at a fixed voltage: using the output mode of the I/O for example or
an external pull-up or pull-down resistor.
I
Symbol
INJ
DD
Injected current on true open-drain pins (PC0 and
PC1)
Injected current on all five-volt tolerant pins
Injected current on all 3.6 V tolerant pins
Injected current on any other pin
(for standard pins) should be avoided during normal product operation. However,
Description
Doc ID 018780 Rev 3
DD
and T
A
unless otherwise specified. All
Functional susceptibility
Negative
injection
STM8L151x2, STM8L151x3
-5
-5
-5
-5
injection
Positive
+0
+0
+0
+5
SS
or
Unit
mA
Related parts for STM8L151G2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STM8 touch sensing library
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM8S207/8 SER
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT TOUCH SENSING STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DAUGHTER FOR STM8S207/8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT MOTOR CONTROL STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Raisonance’s complete, low-cost starter kits for STM8 and ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
EMULATOR FOR STM8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base MCU Target BRD w/Ext BRD
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base Proto 5 Extention Boards
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: